; Configuration file for Duet WiFi (firmware version 1.20 or newer) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool on Fri Jun 15 2018 14:44:46 GMT+0200 (heure d’été d’Europe centrale) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 PEssai 1 ; Set machine name M551 PSTERNE ; Set password M552 P192.168.1.202 S1 ; Enable network ;*** Access point is configured manually via M587 M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M584 U3 ; Définit les axes aux moteurs et ajout de U M569 P0 S1 ; Drive X goes forwards M569 P1 S1 ; Drive Y goes forwards M569 P2 S1 ; Drive Z goes forwards M569 P3 S1 ; Drive E1 goes forwards M569 P4 S1 ; Drive U goes forwards M350 X16 Y16 Z16 E16 U16 I1 ; Configure microstepping with interpolation I1 = enable M92 X80 Y800 Z4000 E420 U80 ; Set steps per mm M566 X900 Y900 Z12 E120 U900 ; Set maximum instantaneous speed changes (mm/min) M203 X1200 Y4000 Z180 E1200 U1200 ; Set maximum speeds (mm/min) M201 X1000 Y1000 Z250 E250 U1000 ; Set accelerations (mm/s^2) M906 X1150 Y1150 Z1150 E800 U1150 I30 ; Set motor currents (mA) and motor idle factor in per cent ;M84 S30 Set idle timeout0 (!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!) ; Axis Limits M208 X0 Y0 Z0 U0 S1 ; Set axis minima M208 X800 Y800 Z800 U1500 S0 ; Set axis maxima ; Endstops ; Z-Probe M574 X2 Y2 Z2 S0 ; Set endstops controlled by probe ;M558 P3 H5 F120 T6000 ; Set Z probe type to ultrasonic and the dive height + speeds ;G31 P100 X0 Y0 Z20 ; Set Z probe trigger value, offset and trigger height ;M557 X15:285 Y15:285 S20 ; Define mesh grid ; Heaters M305 P0 T10000 B3988 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P2 S1 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 U0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured