; Configuration file for Duet WiFi (firmware version 1.19) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool on Wed Aug 02 2017 13:42:53 GMT+0200 (Mitteleuropäische Sommerzeit) ; General preferences M111 S0 ; Debugging off G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M555 P2 ; Set firmware compatibility to look like Marlin M667 S1 ; Select CoreXY mode M208 X0 Y30 Z0 S1 ; Set axis minima M208 X340 Y340 Z340 S0 ; Set axis maxima ; Endstops M574 Z1 S1 ; Define active low and unused microswitches M574 X1 Y1 S1 ; Define active high microswitches ;M558 P1 X0 Y0 Z0 H5 F120 T9600 ; Set Z probe type to unmodulated, the axes for which it is used and the probe + travel speeds ;G31 P600 X0 Y0 Z2.5 ; Set Z probe trigger value, offset and trigger height M557 X15:285 Y15:285 S20 ; Define mesh grid ; Drives M569 P0 S0 ; Drive 0 goes backwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S0 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes backwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80 Y80 Z405 E95 ; Set steps per mm original X80 Y80 566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min) M203 X6000 Y6000 Z1200 E4800 ; Set maximum speeds (mm/min) M201 X700 Y700 Z250 E250 ; Set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Heaters M143 S250 ; Set maximum heater temperature to 260C ;M305 P0 T10000 B3988 C0 R4700 ; Set thermistor + ADC parameters for heater 0 ;M305 P1 T10000 B3988 C0 R4700 ; Set thermistor + ADC parameters for heater 1 ;M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1 M305 P0 R4700 H0 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction ;M305 P1 R4700 C7.0600 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1 ;M305 P2 R4700 H0 L0 ; Put your own H and/or L values here to set the second nozzle thermistor ADC correction ;M301 H1 P10 I0.10 D100 T0.50 S1.0 ; PID settings for extruder 0 ;M301 H2 P10 I0.10 D100 T0.50 S1.0 ; PID settings for extruder 1 M570 S120 ; Increase to allow extra heating time if needed ; Tools M563 P0 D0 H1 F2 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Network M550 PHypercube EVO ; Set machine name M552 S1 ; Enable network M587 S"SSHD-CABLE" P"SHD2492SHD249200" ; Configure access point. You can delete this line once connected M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Fans ;M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P2 S1 I0 F500 H-1; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off ; Custom settings are not configured M106 P2 S0 M106 P0 S0