# generated by Slic3r Prusa Edition 1.41.0+ on 2018-09-07 at 13:20:54
avoid_crossing_perimeters = 0
bed_shape = 10x0,305x0,305x273,10x273
bed_temperature = 55
before_layer_gcode = 
between_objects_gcode = 
bottom_solid_layers = 7
bridge_acceleration = 437.5
bridge_angle = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 40
brim_width = 0.5
clip_multipart_objects = 1
complete_objects = 0
cooling = 1
cooling_tube_length = 5
cooling_tube_retraction = 91.5
default_acceleration = 4250
default_filament_profile = 
default_print_profile = 
deretract_speed = 25
disable_fan_first_layers = 2
dont_support_bridges = 1
duplicate_distance = 6
elefant_foot_compensation = 0.01
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = M0								; Turn off all heaters and call stop.g macro
ensure_vertical_shell_thickness = 1
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 30
external_perimeters_first = 0
extra_loading_move = -2
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_colour = #FFFFFF
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 0.95
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #18BC04
filament_cooling_final_speed = 3.4
filament_cooling_initial_speed = 2.2
filament_cooling_moves = 4
filament_cost = 30
filament_density = 1.25
filament_diameter = 1.72
filament_load_time = 0
filament_loading_speed = 28
filament_loading_speed_start = 3
filament_max_volumetric_speed = 0
filament_minimal_purge_on_wipe_tower = 15
filament_notes = ""
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
filament_settings_id = "AMZ3D PLA Green"
filament_soluble = 0
filament_toolchange_delay = 0
filament_type = PLA
filament_unload_time = 0
filament_unloading_speed = 90
filament_unloading_speed_start = 100
fill_angle = 45
fill_density = 10%
fill_pattern = cubic
first_layer_acceleration = 120
first_layer_bed_temperature = 65
first_layer_extrusion_width = 0
first_layer_height = 0.2
first_layer_speed = 25
first_layer_temperature = 205
gap_fill_speed = 35
gcode_comments = 0
gcode_flavor = reprap
host_type = duet
infill_acceleration = 1750
infill_every_layers = 2
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 25%
infill_speed = 70
interface_shells = 0
layer_gcode = 
layer_height = 0.15
machine_max_acceleration_e = 10000,5000
machine_max_acceleration_extruding = 1500,1250
machine_max_acceleration_retracting = 1500,1250
machine_max_acceleration_x = 9000,1000
machine_max_acceleration_y = 9000,1000
machine_max_acceleration_z = 500,200
machine_max_feedrate_e = 120,120
machine_max_feedrate_x = 500,200
machine_max_feedrate_y = 500,200
machine_max_feedrate_z = 12,12
machine_max_jerk_e = 2.5,2.5
machine_max_jerk_x = 10,10
machine_max_jerk_y = 10,10
machine_max_jerk_z = 0.2,0.4
machine_min_extruding_rate = 0,0
machine_min_travel_rate = 0,0
max_fan_speed = 80
max_layer_height = 0.36
max_print_height = 300
max_print_speed = 300
max_volumetric_extrusion_rate_slope_negative = 0
max_volumetric_extrusion_rate_slope_positive = 0
max_volumetric_speed = 14
min_fan_speed = 40
min_layer_height = 0.05
min_print_speed = 5
min_skirt_length = 10
notes = 
nozzle_diameter = 0.4
only_retract_when_crossing_perimeters = 0
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
parking_pos_retraction = 92
perimeter_acceleration = 875
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 80
perimeters = 3
post_process = 
print_host = 
print_settings_id = D-Bot PLA OPTIMIZED
printer_model = 
printer_notes = “”
printer_settings_id = D-Bot
printer_variant = 
printer_vendor = 
printhost_apikey = 314F742A0D784AE88B03AEAB61449658
printhost_cafile = 
raft_layers = 0
remaining_times = 0
resolution = 0
retract_before_travel = 2
retract_before_wipe = 0%
retract_layer_change = 1
retract_length = 0.8
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 125
seam_position = aligned
serial_port = 
serial_speed = 250000
silent_mode = 1
single_extruder_multi_material = 0
single_extruder_multi_material_priming = 1
skirt_distance = 30
skirt_height = 1
skirts = 3
slowdown_below_layer_time = 5
small_perimeter_speed = 15
solid_infill_below_area = 50
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 70
spiral_vase = 0
standby_temperature_delta = -5
start_filament_gcode = "; Filament gcode\nM307 H0 A82.6 C112.0 D2.7 S1.00 V24.0 B0 ; PID tune for bed at 60c\nM307 H1 A460.6 C173.6 D3.1 S1.00 V23.9 B0 ; Pid tune for hotend at 210c\nM572 D0 S0.06   ; Pressure advance for PLA\nM207 S0.75 R0 F8000 T1200   ; retraction settings for PLA"
start_gcode = M109 S[first_layer_temperature]	; Set extruder to first layer temp and wait\nG10 P0 R100 S[first_layer_temperature]  ; set temp and standby temp\nM116 ; wait for temps\nM98 P"0:/sys/PrimeNozzle.g"\n\nM98 P"0:/sys/StartGCode.g"\n\n; Speed settings for print time estimates in Slic3r PE. (Converted to Marlin values)\n;\n; 	M201 X4250 Y4250 Z60 E6000		; Set maximum accelerations (mm/s^2)\n; 	M203 X30000 Y30000 Z450 E15000 		; Set maximum speeds (mm/min)\n; 	M204 P1500 R7000 T4250 			; sets acceleration (S) and retract acceleration (T)\n; 	M205 X900 Y900 Z60 E3000		; Set maximum instantaneous speed changes (mm/min) (Jerk)
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.15
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0.35
support_material_interface_contact_loops = 0
support_material_interface_extruder = 1
support_material_interface_layers = 2
support_material_interface_spacing = 0.2
support_material_interface_speed = 100%
support_material_pattern = rectilinear
support_material_spacing = 2
support_material_speed = 40
support_material_synchronize_layers = 0
support_material_threshold = 45
support_material_with_sheath = 0
support_material_xy_spacing = 60%
temperature = 205
thin_walls = 1
threads = 8
toolchange_gcode = 
top_infill_extrusion_width = 0
top_solid_infill_speed = 30
top_solid_layers = 10
travel_speed = 233
use_firmware_retraction = 1
use_relative_e_distances = 1
use_volumetric_e = 0
variable_layer_height = 1
wipe = 0
wipe_into_infill = 0
wipe_into_objects = 0
wipe_tower = 0
wipe_tower_bridging = 10
wipe_tower_rotation_angle = 0
wipe_tower_width = 60
wipe_tower_x = 180
wipe_tower_y = 140
wiping_volumes_extruders = 70,70
wiping_volumes_matrix = 0
xy_size_compensation = 0
z_offset = 0