; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool on Fri Sep 14 2018 16:24:32 GMT-0700 (Pacific Summer Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M667 S1 ; Select CoreXY mode ; Network M550 P3d printer ; Set machine name M551 Preprap ; Set password M552 S1 ; Enable network M587 S"Area 52" P"RY67TWF8NT" ; Configure access point. You can delete this line once connected M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S1 ; Drive 0 goes forwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S0 ; Drive 2 goes backwards M569 P3 S0 ; Drive 3 goes backwards M569 P4 S0 ; Drive 4 goes backwards M350 X16 Y16 Z16 E16:16 I1 ; Configure microstepping with interpolation M92 X80 Y80 Z400 E98:98 ; Set steps per mm M566 X900 Y900 Z12 E120:120 ; Set maximum instantaneous speed changes (mm/min) M203 X18000 Y18000 Z180 E1200:1200 ; Set maximum speeds (mm/min) M201 X3000 Y3000 Z100 E10000:10000 ; Set accelerations (mm/s^2) M906 X1100 Y1100 Z1200 E925:925 I35 ; Set motor currents (mA) and motor idle factor in per cent M84 S35 ; Set idle timeout ; Axis Limits M208 X10 Y10 Z0 S1 ; Set axis minima M208 X320 Y320 Z380 S0 ; Set axis maxima ; Endstops M574 X1 Y2 S0 ; Set active low endstops ; Z-Probe M574 Z1 S2 ; Define Z to use Probe. Home to Min M307 H7 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch M558 P9 H5 F120 T4000 ; Set Z probe type to bltouch and the dive height + speeds G31 P25 X-32.08 Y-21.62 Z0 ; Set Z probe trigger value, offset and trigger height M556 S0 X0 Y0 Z0 ; Set orthogonal axis compensation parameters ; Heaters M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S1 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P2 S1 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off ; Tools M563 P0 D0:1 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C M568 P0 S1 ; Enable mixing for tool 0 M567 P0 E0.5:0.5 ; Set mixing ratios for tool 0 ; Automatic power saving M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss ; Custom settings are not configured ; Miscellaneous T0 ; Select first tool