; Configuration file for Duet Ethernet (firmware version 1.17) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool on Sat Jun 17 2017 22:30:42 GMT+0200 (CEST) ; General preferences M111 S0 ; Debugging off G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M555 P2 ; Set firmware compatibility to look like Marlin M208 X0 Y0 Z0 S1 ; Set axis minima M208 X260 Y250 Z295 S0 ; Set axis maxima ; Endstops M574 X1 Y1 Z1 S0 ; Define active low and unused microswitches M558 P4 H5 F120 I1 T6000 ; Set Z probe type to switch, the axes for which it is used and the probe + travel speeds G31 P600 X47 Y43 Z1.86 ; Set Z probe trigger value, offset and trigger height Glass + 3D Lac ; G31 P600 X47 Y43 Z2.16 ; Set Z probe trigger value, offset and trigger height PEI sheet M557 X50:250 Y50:250 S50 ; Define mesh grid M376 H2 ; Set bed compensation taper ; Drives M569 P0 S0 ; Drive 0 goes backwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S1 ; Drive 3 goes forwards M569 P4 S0 ; Drive 4 goes backwards M350 X16 Y16 Z16 E16:16 I1 ; Configure microstepping with interpolation M92 X160.47 Y160.11 Z1600 E505.7:505.7 ; Set steps per mm M566 X360 Y360 Z24 E1200:1200 ; Set maximum instantaneous speed changes (mm/min) M203 X18000 Y18000 Z360 E2400:2400 ; Set maximum speeds (mm/min) M201 X1500 Y1500 Z300 E3000:3000 ; Set accelerations (mm/s^2) M906 X1100 Y1100 Z850 E600:600 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S15 ; Set idle timeout ; Heaters M143 H1 S320 ; Set maximum heater temperature to 320C M143 H2 S320 ; Set maximum heater temperature to 320C M143 H0 S120 ; set the maximum bed temperature to 120C M305 P0 T100000 B4092 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M305 P1 T100000 B4138 C0 X200 F50; Set thermistor + ADC parameters for heater 1 and remap it to channel 200 M305 P2 T100000 B4138 C0 X201 F50; Set thermistor + ADC parameters for heater 2 and remap it to channel 201 M307 H1 A599.7 C247.3 D5.5 B0 M307 H2 A485.4 C214.6 D5.0 B0 ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C M563 P1 D1 H2 ; Define tool 1 G10 P1 X23.5 Y-0.4 Z0 ; Set tool 1 axis offsets G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C ; Network M550 PMankati ; Set machine name M540 PBE:EF:DE:AD:FE:ED ; Set MAC address M552 S1 P10.147.2.122 M553 P255.255.255.0 ; Set netmask M554 P10.147.2.1 ; Set gateway M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Fans M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T40 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P2 S1 I0 F500 H2 T40 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Custom settings are not configured ; Miscellaneous T0 ; Select first tool M911 S22.0 R24.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set resume on failure