; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Wed Nov 21 2018 20:47:24 GMT+0100 (Central European Standard Time)

; General preferences
G90                                         ; Send absolute coordinates...
M83                                         ; ...but relative extruder moves
M665 R166.104 L360.21 B110 H335.399 X0.079 Y0.551 Z0   ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X-0.41 Y0.43 Z0.0                      ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 P"FrankenKossel"                       ; Set machine name
M552 S1                                     ; Enable network
M587 S"sssss" P"ppppp"                      ; Configure access point. You can delete this line once connected
M586 P0 S1                                  ; Enable HTTP
M586 P1 S1                                  ; Enable FTP
M586 P2 S1                                  ; Enable Telnet

; Drives
M569 P0 S1                                  ; Drive 0 goes forwards
M569 P1 S1                                  ; Drive 1 goes forwards
M569 P2 S1                                  ; Drive 2 goes forwards
M569 P3 S0                                  ; Drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1                     ; Configure microstepping with interpolation
M92 X100.00 Y100.00 Z100.00 E98.50          ; Set steps per mm
M566 X150.00 Y150.00 Z150.00 E300.00        ; Set maximum instantaneous speed changes (mm/min)
M200 D1.75                                  ; Filament diameter for volumetric E
M201 X800.00 Y800.00 Z800.00 E8000.00       ; Set accelerations (mm/s^2)
M203 X48000.00 Y48000.00 Z48000.00 E6000.00 ; Set maximum speeds (mm/min)
M207 S3.0 F3000 Z0.1                        ; firmware retract
M572 D0 S0.15                                ; pressure advance
M906 X1000.00 Y1000.00 Z1000.00 E1200.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                     ; Set idle timeout

; Axis Limits
M208 Z0 S1                                  ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1                               ; Set active high endstops

; Z-Probe
; M574 Z2 S2                                  ; Set endstops controlled by probe
M558 P5 R0.4 H5 F1200 T6000                 ; Set Z probe type to effector and the dive height + speeds
G31 P500 X0 Y0 Z0.313                       ; Set Z probe trigger value, offset and trigger height
M557 R110 S20                               ; Define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700                 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                                ; Set temperature limit for heater 1 to 280C

; Nozzle

M404 N1.75 D0.3                             ; Set filament diameter to 1.75mm, nozzle diameter to 0.3mm (on new e3d block, this is true).

; Fans
M106 P0 S0.7 I0 F500 H-1                    ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                   ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                               ; Define tool 0
G10 P0 X0 Y0 Z0                             ; Set tool 0 axis offsets
G10 P0 R0 S0                                ; Set initial tool 0 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured

; Miscellaneous
M375                                        ; Load heightmap
M501                                        ; Load saved parameters from non-volatile memory