3:05:53 PM: Connection established!
3:05:52 PM: Disconnected.
3:05:43 PM: : Warning: VIN over-voltage event (24.1V)
3:05:39 PM: Connection established!
3:05:36 PM: Disconnected.
3:05:29 PM: : Warning: VIN over-voltage event (24.3V)
3:05:24 PM: : Warning: VIN over-voltage event (31.5V)
3:05:20 PM: : Warning: VIN over-voltage event (24.2V)
3:05:15 PM: : Warning: VIN over-voltage event (36.3V)
3:05:11 PM: : Warning: VIN over-voltage event (32.7V)
3:05:09 PM: : Warning: VIN over-voltage event (24.2V)
3:05:02 PM: : Warning: VIN over-voltage event (28.6V)
3:04:57 PM: : Warning: VIN over-voltage event (24.1V)
3:04:53 PM: : Warning: VIN over-voltage event (24.1V)
3:04:52 PM: : Warning: VIN over-voltage event (36.3V)
3:04:44 PM: : Warning: VIN over-voltage event (24.1V)
3:04:42 PM: : Warning: VIN over-voltage event (36.3V)
3:04:35 PM: : Warning: VIN over-voltage event (36.3V)
3:04:31 PM: : Warning: VIN over-voltage event (24.1V)
3:04:27 PM: : Warning: VIN over-voltage event (36.3V)
3:04:25 PM: : Error: Cannot read file, error code 1.Cancelled printing file P_rook_compoundnozzle.gcode, print time was 0h 3m
3:04:21 PM: : Warning: VIN over-voltage event (34.4V)
3:02:16 PM: G10 P0 S189
3:01:15 PM: M32 ""P_rook_compoundnozzle.gcode"": File P_rook_compoundnozzle.gcode selected for printing
3:00:38 PM: G10 P0 S189
3:00:33 PM: T0
3:00:32 PM: G10 P0S-273.15 R-273.15
3:00:10 PM: M140 S40
3:00:04 PM: G10 P0 S189
2:58:27 PM: M292: 64 points probed, mean error 0.488, deviation 0.480Height map saved to file heightmap.csv
2:54:01 PM: M292
2:52:38 PM: : Record the Z axis value displayed in the Machine Status
2:52:37 PM: : If the value is 0, then skip to running the _3_Mesh_Bed.g macro
2:52:36 PM: : Otherwise set the G92 Z value in machine_zendstop.g
2:52:35 PM: : If the recorded Z value is - (negative), ADD it to the current Z value
2:52:34 PM: : If the recorded Z value is + (positive), SUBTRACT it from the current Z value
2:52:33 PM: : Edit machine_axisdimension.g and set max Z to the next whole number above the new Z end stop set in machine_zendstop.g
2:52:31 PM: M292: After both files are saved run the _2_Set_Z_Endstop_Height.g macro again until no correction is needed.. End of Message...
2:49:33 PM: M292
2:43:17 PM: M98 P""0:/macros/macros_here.g""
2:41:22 PM: G28
2:38:08 PM: G28
2:37:20 PM: M120G91G1 Z25 F6000M121: Error: G0/G1: insufficient axes homedError: Pop(): stack underflow!
2:37:14 PM: M120G91G1 Z25 F6000M121: Error: G0/G1: insufficient axes homedError: Pop(): stack underflow!
2:37:06 PM: Connection established!
2:37:06 PM: Page Load complete!