; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Wed Jan 23 2019 16:41:23 GMT+0100 (Central European Standard Time) ;**************************************************************************************************** ; General preferences ;**************************************************************************************************** G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ;**************************************************************************************************** ;Delta Parameters ;**************************************************************************************************** M665 L267.500 R110 H295.44 B100.0 X-0.000 Y0.000 Z0.000 ;L-Rods, R-Delta Radius, H-Homed Height, B-Printable Bed, Size XYZ-Twist M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them ;**************************************************************************************************** ; Network ;**************************************************************************************************** M550 P"GTsDelta" ; Set machine name M551 P"reprap: ; Set password M552 S1 ; Enable network ;M587 S"" P"" I192.168.0.40 J192.168.0.1 K255.255.255.0 ; Configure access point and IP addresses. You can delete this line once connected M586 P0 S1 ; Enable HTTP M586 P1 S1 ; Enable FTP M586 P2 S1 ; Enable Telnet ;**************************************************************************************************** ; Drives ;**************************************************************************************************** ;Direction M569 P0 S0 ; Drive 0 (X) goes backwards M569 P1 S0 ; Drive 1 (Y) goes backwards M569 P2 S0 ; Drive 2 (Z) goes backwards M569 P3 S1 ; Drive 3 (E0) goes forward M569 P4 S1 ; Drive 4 (E1) goes forward ;Stepping M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80.00 Y80.00 Z80.00 E94.80 ; Set steps per mm ;Speed M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; Set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; Set accelerations (mm/s^2) M906 X1000.00 Y1000.00 Z1000.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ;**************************************************************************************************** ; Axis Limits ;**************************************************************************************************** M208 Z0 S1 ; Set minimum Z ;**************************************************************************************************** ; Endstops ;**************************************************************************************************** M574 X2 Y2 Z2 S1 ; Set active high endstops ;**************************************************************************************************** ; Z-Probe ;**************************************************************************************************** M307 H3 A-1 C-1 D-1 ; Disable heater 3 on PWM channel for BLTouch M558 P9 H5 F100 T2000 ; Set Z probe type to bltouch and the dive height + speeds (probe type/mode 5. H=Dive Height. F=Speed the bed moves) G31 P25 X0 Y-40 Z2.5 ; Set Z probe trigger value, offset and trigger height M557 R90 S20 ; Define mesh grid ;**************************************************************************************************** ; Heaters ;**************************************************************************************************** ;Bed ;M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning); ;M305 P0 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 0 ;Extruder 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120CM140 H-1 M305 P1 T100000 B4725 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ;**************************************************************************************************** ; Fans ;**************************************************************************************************** M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on ;**************************************************************************************************** ; Tools ;**************************************************************************************************** M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ;**************************************************************************************************** ;Pressure Advance ;**************************************************************************************************** ;M572 D0 S0.1 ;**************************************************************************************************** ; Calibration ;**************************************************************************************************** ;M501 ; Load congif overide calibration settings ;M302 P1 ; Allow cold extrusion ;**************************************************************************************************** ; Automatic saving after power loss is not enabled ;**************************************************************************************************** ;**************************************************************************************************** ; Custom settings are not configured ;****************************************************************************************************