12:53:12 PM: M122: === Diagnostics ===RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02RC5(RTOS) running on Duet WiFi 1.02 or laterBoard ID: 08DGM-917NK-F23T0-6J1DG-3SN6L-1H80GUsed output buffers: 1 of 20 (9 max)=== RTOS ===Static ram: 27284Dynamic ram: 98384 of which 0 recycledException stack ram used: 392Never used ram: 5012Tasks: NETWORK(ready,400) HEAT(blocked,1232) MAIN(running,3840) IDLE(ready,200)Owned mutexes:=== Platform ===Last reset 00:05:51 ago, cause: power upLast software reset at 2019-01-27 20:34, reason: User, spinning module GCodes, available RAM 5020 bytes (slot 3)Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414dError status: 0Free file entries: 9SD card 0 detected, interface speed: 20.0MBytes/secSD card longest block write time: 13.5ms, max retries 0MCU temperature: min 14.7, current 25.3, max 25.5Supply voltage: min 23.4, current 23.8, max 24.1, under voltage events: 0, over voltage events: 0, power good: yesDriver 0: ok, SG min/max 0/485Driver 1: standstill, SG min/max 0/1023Driver 2: standstill, SG min/max 102/498Driver 3: standstill, SG min/max 0/1023Driver 4: standstill, SG min/max not availableDate/time: 2019-01-28 12:53:11Cache data hit count 1227740729Slowest loop: 130.75ms; fastest: 0.07msI2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0=== Move ===Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 237, MinFreeDm: 234, MaxWait: 26056ms, Underruns: 0, 0Scheduled moves: 74, completed moves: 71Bed compensation in use: noneBed probe heights: 0.000 0.000 0.000 0.000 0.000=== Heat ===Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1=== GCodes ===Segments left: 1Stack records: 2 allocated, 0 in useMovement lock held by nullhttp is idle in state(s) 0telnet is idle in state(s) 0file is doing ""G0X55.563Y50.800"" in state(s) 0serial is idle in state(s) 0aux is idle in state(s) 0daemon is idle in state(s) 0queue is idle in state(s) 0autopause is idle in state(s) 0Code queue is empty.=== Network ===Slowest loop: 24.26ms; fastest: 0.00msResponder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)HTTP sessions: 1 of 8- WiFi -Network state is runningWiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0WiFi firmware version 1.21WiFi MAC address bc:dd:c2:89:a1:bdWiFi Vcc 3.42, reset reason Turned on by main processorWiFi flash size 4194304, free heap 16864WiFi IP address 192.168.1.105WiFi signal strength -56dBm, reconnections 0, sleep mode modemSocket states: 0 0 0 0 0 0 0 0 12:52:44 PM: M220 S100 12:49:44 PM: M220 S300 12:49:37 PM: M220 S207 12:49:12 PM: M32 ""Reuben Base 2.gcode"": File Reuben Base 2.gcode selected for printingWarning: G17 command is not supported 12:48:46 PM: G28 12:48:24 PM: M98 P""0:/macros/Work Coordinate System/B2 - Set Work Coordinates"" 12:48:07 PM: M120G91G1 Z-5 F6000M121 12:48:06 PM: M120G91G1 Z-5 F6000M121 12:48:01 PM: M120G91G1 X-50 F6000M121 12:47:59 PM: M120G91G1 X-50 F6000M121 12:47:58 PM: M120G91G1 X-50 F6000M121 12:47:57 PM: M120G91G1 X-50 F6000M121 12:47:56 PM: M120G91G1 X-50 F6000M121 12:47:55 PM: M120G91G1 X-50 F6000M121 12:47:54 PM: M120G91G1 X-50 F6000M121 12:47:52 PM: M120G91G1 X-50 F6000M121 12:47:51 PM: M120G91G1 X-50 F6000M121 12:47:47 PM: M120G91G1 Y-50 F6000M121 12:47:46 PM: M120G91G1 Y-50 F6000M121 12:47:44 PM: M120G91G1 Y-50 F6000M121 12:47:43 PM: M120G91G1 Y-50 F6000M121 12:47:42 PM: M120G91G1 Y-50 F6000M121 12:47:40 PM: G28 12:47:35 PM: Connection established! 12:47:35 PM: Page Load complete!