; Configuration file for My Printer ; Communication and general M111 S0 ; Debug off M550 RailDog ; Machine name and Netbios name (can be anything you like) ;M551 Pmyrap ; Machine password (used for FTP) ;*** If you have more than one Duet on your network, they must all have different MAC addresses, so change the last digits M540 P0xBE:0xEF:0xDE:0xAD:0xFE:0xEE ; MAC Address ;*** Wifi Networking M552 S1 ; Enable WiFi M555 P2 ; Set output to look like Marlin M575 P1 B57600 S1 ; Comms parameters for PanelDue G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Axis and motor configuration M667 S1 ; CoreXY mode M584 X0 Y1 Z5:6:7 E3:4:8:9 ; Map Z to drivers 5, 6, 7. Define unused drivers 3,4,8 and 9 as extruders M569 P0 S1 ; Drive 0 goes forwards (change to S0 to reverse it) X stepper M569 P1 S0 ; Drive 1 goes backwards Y Stepper M569 P2 S1 ; Drive 2 goes forwards Unused M569 P3 S1 ; Drive 3 goes forwards Extruder M569 P4 S1 ; Drive 4 goes forwards Extruder (unused) M569 P5 S1 ; Drive 5 goes backwards Front Left Z M569 P6 S1 ; Drive 6 goes backwards Rear Left Z M569 P7 S1 ; Drive 7 goes backwards Right Z ;Leadscrew locations M671 X-10.5:-10.5:348 Y22:278.5:150 S20 ;Front left, Rear Left, Right S7.5 is the max correction - measure your own offsets, to the bolt for the yoke of each leadscrew M350 X16 Y16 Z16 E16 I1 ; set 16x microstepping for axes& extruder, with interpolation M574 X1 Y1 Z0 S1 ; set homing switch configuration (x,y at min, z at max) IF YOU NEED TO REVERSE YOUR HOMING SWITCHES CHANGE S1 to S0 M906 X1400 Y1400 Z1000 E1250 I60 ; Set motor currents (mA) M201 X3000 Y3000 Z20 E1000 ; Accelerations (mm/s^2) M203 X24000 Y24000 Z900 E3600 ; Maximum speeds (mm/min) M566 X1000 Y1000 Z30 E20 ; Maximum jerk speeds mm/minute M208 X300 Y302 Z610 ; set axis maxima and high homing switch positions (adjust to suit your machine) M208 X0 Y0 Z-0.5 S1 ; set axis minima and low homing switch positions (adjust to make X=0 and Y=0 the edges of the bed) M92 X200 Y200 Z1600 E809 ; steps/mm, X/Y may be more around 201.5 for accuracy ; Thermistors M305 P0 T100000 B4240 R4700 H0 L0 ; Put your own H and/or L values here to set the bed thermistor ADC correction M305 P1 T100000 B4240 R4700 H0 L0 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction M307 H0 A302.8 C933.9 D11.9 S1.00 V24.0 B0 ; Bed Heaters M307 H1 A508.9 C260.6 D2.2 S1.00 V24.0 B0 ;Heater 1 model M570 S360 ; Hot end may be a little slow to heat up so allow it 180 seconds M143 S285 ; Fans M106 P0 H-1 ; disable thermostatic mode for fan 0 M106 P1 H-1 ; disable thermostatic mode for fan 1 M106 P2 H-1 M106 P0 S0 ; turn off fans M106 P1 S0 M106 P2 S0 ; Tool definitions M563 P0 D0 H1 ; Define tool 0 G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures ;*** If you have a single-nozzle build, comment the next 2 lines ;M563 P1 D1 H2 ; Define tool 1 ;G10 P1 S0 R0 X0 Y17 ; Set tool 1 operating and standby temperatures ; Z probe and compensation definition ;*** If you have a switch instead of an IR probe, change P1 to P4 in the following M558 command ; IR PRobe - uncomment if you have a and IR Probe, and comment out the BLTouch section below ;M558 P1 X0 Y0 Z1 ; Z probe is an IR probe and is not used for homing any axes ;G31 X0 Y30 Z1.95 P500 ; Set the zprobe height and threshold (put your own values here) ;BLTouch - comment out if using a IR Probe M307 H3 A-1 C-1 D-1 M558 P9 X0 Y0 Z1 H5 F50 T6000 A5 S0.02 G31 X2 Y42 Z1.55 P25 ; Tip: A larger trigger height in G31 moves you CLOSER to the bed M208 S1 Z-0.2 ; set minimum Z ; T0 ; select first hot end