01/05/2019, 20:15:27: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -6.3, brightness 30, shutter 132, quality 223, no calibration data
01/05/2019, 20:19:55: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -7.6, brightness 30, shutter 132, quality 223, measured min 129% avg 150% max 202% over 173.6mm
01/05/2019, 20:42:55: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -8.9, brightness 20, shutter 116, quality 221, measured min 125% avg 152% max 234% over 1010.7mm
01/05/2019, 20:43:38: M591 D0 A0
01/05/2019, 20:43:50: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 8.0, brightness 0, shutter 0, no calibration data
01/05/2019, 20:44:13: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -8.1, brightness 0, shutter 0, measured min 141% avg 149% max 179% over 15.2mm
01/05/2019, 20:53:25: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 10.0, brightness 0, shutter 0, measured min 132% avg 144% max 181% over 245.3mm
01/05/2019, 21:20:30: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -9.4, brightness 0, shutter 0, measured min 129% avg 145% max 181% over 986.9mm
01/05/2019, 21:21:52: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -7.1, brightness 0, shutter 0, measured min 129% avg 144% max 181% over 1023.2mm
01/05/2019, 21:22:18: M591 D0 A1
01/05/2019, 21:22:35: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 3.7, brightness 0, shutter 0, no calibration data
01/05/2019, 21:22:49: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -6.4, brightness 0, shutter 0, measured min 144% avg 144% max 144% over 12.1mm
01/05/2019, 21:32:24: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 5.2, brightness 0, shutter 0, measured min 127% avg 151% max 228% over 332.0mm
01/05/2019, 21:34:11: Upload of calicat 0.2 layer ri blue 200 195.gcode successful after 2s
01/05/2019, 21:34:29: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 4.0, brightness 27, shutter 109, quality 223, measured min 127% avg 151% max 228% over 359.1mm
01/05/2019, 21:35:08: M591 D0 A0
01/05/2019, 21:35:20: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -6.7, brightness 12, shutter 117, quality 223, measured min 127% avg 151% max 228% over 365.1mm
01/05/2019, 21:35:42: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 9.4, brightness 25, shutter 126, quality 222, no calibration data
01/05/2019, 21:36:30: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 4.9, brightness 17, shutter 105, quality 224, no calibration data
01/05/2019, 21:36:44: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 3.9, brightness 30, shutter 133, quality 223, no calibration data
01/05/2019, 21:36:58: : Finished printing file 0:/gcodes/calicat 0.16 layer ri blue 200 195.gcode, print time was 1h 26m
01/05/2019, 21:38:23: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03beta3 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4SD-6J9FD-3SJ6J-K593W
Used output buffers: 3 of 20 (11 max)
=== RTOS ===
Static ram: 25632
Dynamic ram: 93736 of which 0 recycled
Exception stack ram used: 476
Never used ram: 11228
Tasks: NETWORK(ready,652) HEAT(blocked,1172) MAIN(running,356) IDLE(ready,196)
Owned mutexes:
=== Platform ===
Last reset 01:34:46 ago, cause: power up
Last software reset at 2019-05-01 19:43, reason: User, spinning module GCodes, available RAM 11180 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 2
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 9.6ms, max retries 0
MCU temperature: min 22.4, current 34.7, max 36.5
Supply voltage: min 11.5, current 12.2, max 12.6, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max 0/1023
Driver 1: standstill, SG min/max 0/1023
Driver 2: standstill, SG min/max 0/1023
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2019-05-01 21:38:21
Cache data hit count 4294967295
Slowest loop: 64.44ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 278, FreeDm: 169, MinFreeDm: 101, MaxWait: 270717ms
Bed compensation in use: mesh
Bed probe heights: -0.020 -0.141 0.065 -0.085 -0.036
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 1, LaErrors: 0, Underruns: 0, 0
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 0, aux move: no
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 56.36ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 5c:cf:7f:2c:24:6b
WiFi Vcc 3.37, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 23088
WiFi IP address 192.168.1.16
WiFi signal strength -52dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0: pos 6.92, ok, no calibration data, errs: frame 0 parity 0 ovrun 0 pol 0 ovdue 0