09/05/2019, 16:37:08: G32: Calibrated 6 factors using 17 points, deviation before 0.379 after 0.065
09/05/2019, 16:39:04: G32: Calibrated 6 factors using 17 points, deviation before 0.681 after 0.046
09/05/2019, 16:40:06: M32 "0:/gcodes/Great_Dodecahedron_v1bblacl pla.gcode": File 0:/gcodes/Great_Dodecahedron_v1bblacl pla.gcode selected for printing
09/05/2019, 16:44:58: M591 D0: Duet3D laser filament monitor v2 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -0.5, brightness 30, shutter 122, quality 223, measured min 113% avg 144% max 195% over 115.3mm
09/05/2019, 16:45:18: M591 D0 A0
09/05/2019, 16:45:24: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -5.3, brightness 0, shutter 0, no calibration data
09/05/2019, 16:45:39: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -0.2, brightness 0, shutter 0, measured min 145% avg 145% max 145% over 12.1mm
09/05/2019, 16:45:53: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 7.3, brightness 0, shutter 0, measured min 134% avg 142% max 145% over 18.2mm
09/05/2019, 16:47:31: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos -2.6, brightness 0, shutter 0, measured min 124% avg 138% max 156% over 92.0mm
09/05/2019, 16:47:51: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03RC1 running on Duet WiFi 1.0 or 1.01
Board ID: 08DAM-999TL-MQ4SD-6J9FD-3SJ6J-K593W
Used output buffers: 5 of 24 (18 max)
=== RTOS ===
Static ram: 25656
Dynamic ram: 93776 of which 0 recycled
Exception stack ram used: 476
Never used ram: 11164
Tasks: NETWORK(ready,652) HEAT(blocked,1172) MAIN(running,356) IDLE(ready,156)
Owned mutexes:
=== Platform ===
Last reset 01:29:56 ago, cause: power up
Last software reset at 2019-05-03 17:10, reason: User, spinning module GCodes, available RAM 11244 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 21.4ms, max retries 0
MCU temperature: min 31.0, current 34.0, max 34.2
Supply voltage: min 11.7, current 12.1, max 12.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/1023
Driver 1: ok, SG min/max 0/591
Driver 2: ok, SG min/max 0/388
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Date/time: 2019-05-09 16:47:49
Cache data hit count 4294967295
Slowest loop: 64.53ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 16, FreeDm: 162, MinFreeDm: 89, MaxWait: 1577112ms
Bed compensation in use: mesh
Bed probe heights: -0.711 -0.648 -0.505 -0.664 -0.910
=== DDARing ===
Scheduled moves: 7183, completed moves: 7143, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.3
Heater 1 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X1.304 Y-17.885 E0.01261" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.16ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 1
WiFi firmware version 1.23
WiFi MAC address 5c:cf:7f:2c:24:6b
WiFi Vcc 3.37, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 22608
WiFi IP address 192.168.1.16
WiFi signal strength -50dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0: pos -1.53, ok, measured min 124% avg 138% max 156% over 107.3mm, errs: frame 6 parity 0 ovrun 0 pol 1 ovdue 0
09/05/2019, 16:48:11: M591 D0: Duet3D laser filament monitor v1 on input 3, disabled, allow 40% to 160%, check every 3.0mm, current pos 8.0, brightness 0, shutter 0, measured min 124% avg 138% max 171% over 125.8mm