; Configuration file for Duet Maestro (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Sat Mar 16 2019 23:24:37 GMT+0100 (Mitteleuropäische Normalzeit) ; edited by tcj, nealz ; if everything but the board is unchanged and connected as Duet3D recommends ; General preferences M111 S0 ; Debug off G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M555 P2 ; Set output to look like Marlin ; Network M550 P"Anycubic Predator" ; Set machine name M551 Preprap ; Machine password (used when you connect Duet Web Control or via FTP) M552 S1 ; Enable network and acquire dynamic address via DHCP M586 P0 S1 ; Enable HTTP M586 P1 S1 ; Enable FTP (enable or disable for your needs) M586 P2 S1 ; Enable Telnet (enable or disable for your needs) ; Drives M569 P0 S0 D3 V100 ; Drive 0 (X) goes forwards, stealthChop mode, switch from stealthChop to to spreadCycle mode only at high speeds M569 P1 S0 D3 V100 ; Drive 1 (Y) same as Drive 0 M569 P2 S0 D3 V100 ; Drive 2 (Z) same as Drive 0 M569 P3 S1 D2 ; Drive 3 (Extruder) goes backwards, spreadCycle mode M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80.00 Y80.00 Z80.00 E436.85 ; Set steps per mm ; the following speed and acceleration values are transfered from the original firmware, might be tuned later M201 X1100.00 Y1100.00 Z1100.00 E1100.00 ; Set accelerations (mm/s^2) M203 X9000.00 Y9000.00 Z9000.00 E4800.00 ; Set maximum speeds (mm/min) M566 X1500.00 Y1500.00 Z1500.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min) M906 X800.00 Y800.00 Z800.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Delta configuration M665 R227 L440 B185 H455 ; Set delta radius, diagonal rod length, printable radius and homed height M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them ; Axis Limits M208 Z0 S1 ; Set minimum Z ; Endstops M574 X2 Y2 Z2 S1 ; all endstops at high end, active high ; Z-Probe M558 P4 H10 F240 T6000 ; Set Z probe type to switch and the dive height + speeds G31 X0 Y0 Z38.11 ; Set Z probe trigger value, offset and trigger height - must be adjusted for your machine chnge P500 M557 R185 S20 ; Define mesh grid ; Heaters ;M305 P0 T100000 B3950 R2200 ; Set thermistor + ADC parameters for heater 0 (thermistor type guessed) ;M305 P1 T100000 B3950 R2200 ; Set thermistor + ADC parameters for heater 1 (thermistor type guessed) ;M307 H0 A137.8 C533.3 D1.5 V24.3 B0 ; PID parameters for heatbed - must be adjusted for your machine ;M307 H1 A503.5 C107.0 D9.3 V24.3 B0 ; PID parameters for hotend - must be adjusted for your machine ;M143 H0 S120 ; Set temperature limit for heater 0 to 120C ;M143 H1 S250 ; Set temperature limit for heater 1 to 280C ;### Heaters ### ; H0 = BED ; H1 = Hotend M305 P0 T100000 B3950 R2200 ; Set thermistor + ADC parameters for heater 0 (thermistor type guessed) M305 P0 T100000 B4725 C7.060000e-8 R4700 ; TESTNIELS M305 P1 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 1 M307 H0 A137.8 C533.3 D1.5 V24.3 B0 ; PID parameters for heatbed - must be adjusted for your machine M307 H1 A503.5 C107.0 D9.3 V24.3 B0 ; PID parameters for hotend - must be adjusted for your machine M143 H0 S130 ; Set temperature limit for heater 0 to 120C M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S0 I0 F100 H-1 C"Print Cooling" ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F100 H1 T45 C"Heatsink" ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P2 S1 I0 F100 H100:101 T40 C"Board" ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M200 D0 ; turn volumetric control off M563 P0 D0 H1 F0 ; Define tool 0, extruder 0, Heater 1, Fan 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C T0 ; select tool 0 ; Filament Sensor M591 D0 P0 C3 S1 ; Automatic saving after power loss is not enabled ; Custom settings are not configured ; if you changed to 12V, uncomment the next line ;M98 P12V.g ; if you changed to a Bondtech BMG (Clone), uncomment the next line ;M98 PBondtechBMG.g ; Miscellaneous M501 ; Load saved parameters from non-volatile memory