; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Tue May 28 2019 12:00:40 GMT-0500 (Central Daylight Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 P"Test Bench" ; Set machine name M552 S1 ; Enable network M587 S"NETGEAR06" P"DPPXLSDPE" ; Configure access point. You can delete this line once connected M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S1 ; Physical drive X goes forwards M569 P1 S1 ; Physical drive Y goes forwards M569 P2 S1 ; Physical drive Z goes forwards M569 P5 S0 ; Physical drive EXT goes backwards M584 X0 Y1 Z2 E5 ; Apply custom drive mapping M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X120.31 Y120.31 Z800.00 E100.00 ; Set steps per mm M566 X900.00 Y900.00 Z12.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min) M203 X12000.00 Y12000.00 Z1500.00 E9000.00 ; Set maximum speeds (mm/min) M201 X300.00 Y300.00 Z20.00 E250.00 ; Set accelerations (mm/s^2) M906 X2400.00 Y2400.00 Z2400.00 E2200.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; Set axis minima M208 X1140 Y1140 Z400 S0 ; Set axis maxima ; Endstops M574 X1 Y1 S1 ; Set active high endstops ; Z-Probe M574 Z1 S2 ; Set endstops controlled by probe M558 P2 H5 F300 T6000 ; Set Z probe type to modulated and the dive height + speeds G31 P500 X5 Y0 Z5 ; Set Z probe trigger value, offset and trigger height M557 X50:1100 Y50:1100 S60 ; Define mesh grid ; Heaters M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit M305 P0 X151 ; Configure thermocouple for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 X150 ; Configure thermocouple for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 S"Extruder 1" D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic power saving M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss ; Custom settings are not configured ; Miscellaneous M501 ; Load saved parameters from non-volatile memory