; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Sat May 18 2019 17:29:31 GMT+0200 (Central European Summer Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 P"CR20" ; Set machine name M552 S1 ; Enable network M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S1 ; Physical drive 0 goes forwards (X) M569 P1 S1 ; Physical drive 1 goes forwards (Y) M569 P2 S0 ; Physical drive 2 goes backwards (Z left) M569 P3 S1 ; Physical drive 3 goes forwards (E) M569 P4 S0 ; Physical drive 4 goes backwards (Z right) ; motor definitions M584 X0 Y1 Z2:4 ; X:X Y:Y Zleft:Z; Zright:E1 M671 X-27:263; lead screw positions M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80.00 Y80.00 Z400.00 E95.00 ; Set steps per mm M566 X300.00 Y300.00 Z24.00 E600.00 ; Set maximum instantaneous speed changes (mm/min) M203 X18000.00 Y18000.00 Z300.00 E6000.00 ; Set maximum speeds (mm/min) M201 X500.00 Y500.00 Z100.00 E1000.00 ; Set accelerations (mm/s^2) M906 X1000.00 Y1000.00 Z1000.00 E1200.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y-5 Z0 S1 ; Set axis minima M208 X235 Y235 Z195 S0 ; Set axis maxima ; Endstops M574 X1 Y1 S1 ; Set active high endstops M574 Z1 S2 ; Z probe for Z endstop M591 D0 P2 C3 S1 ; Filament-out sensor on E0 endstop, active high ; Z-Probe M558 P0 H5 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed ; Heaters ; M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit M307 H0 A148.2 C547.8 D0.6 S1.00 V24.3 B0 ; PID tuned values for bed M307 H1 A484.1 C164.6 D5.0 S1.00 V24.5 B0 ; PID tuned values for hotend with sock and no part cooling M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S110 ; Set temperature limit for heater 0 to 110C M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S0 I0 F10 H-1 ; Set fan 0 (hotend). Thermostatic control is turned off. M106 P1 S1 I0 F250 H1 T45 ; Set fan 1 value (heatbreak). Thermostatic control is turned on. M106 P2 S1 I0 F250 H1:100:101:102 T40 ; Set fan 2 value (board), Thermostatic control is turned on. ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured ; Miscellaneous T0 ; Select first tool ; Touch mi probe M558 P8 F300 H5 I0 T4000 ; simple probe G31 P500 X-46 Y-9 Z2.154 ; offsets M557 X50:170 Y50:170 S20 ; grid probe for G29