; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Tue Apr 02 2019 08:41:38 GMT+0200 (Mitteleuropäische Sommerzeit) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 XXXXXXXXXXXXXXXXXXXXXX ; Set machine name M551 XXXXXXXXXXXXXXXXXXXXXX ; Set password M552 XXXXXXXXXXXXXXXXXXXXXX ; Enable network and acquire dynamic address via DHCP M586 P0 S1 ; Enable HTTP M586 P1 S1 ; Enable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S1 ; Drive 0 goes forwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S0 ; Drive 2 goes backwards M569 P3 S1 ; Drive 3 goes forwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80.00 Y80.00 Z640.00 E1280.00 ; Set steps per mm M566 X900.00 Y900.00 Z900.00 E900.00 ; Set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z3600.00 E3600.00 ; Set maximum speeds (mm/min) M201 X500.00 Y500.00 Z3000.00 E500.00 ; Set accelerations (mm/s^2) M906 X800.00 Y800.00 Z1800.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; Set axis minima M208 X250 Y140 Z350 S0 ; Set axis maxima ; Endstops M574 X0 Y0 Z2 S0 ; Set active low and disabled endstops ; Z-Probe M558 P0 H5 F1200 T3600 ; Disable Z probe but set dive height, probe speed and travel speed M557 X15:235 Y15:140 S20 ; Define mesh grid ; Heaters M305 P0 X205 ; Configure PT100 for heater 0 M143 H0 S80 ; Set temperature limit for heater 0 to 80C M305 P1 X204 ; Configure PT100 for heater 1 M143 H1 S80 ; Set temperature limit for heater 1 to 80C ; Fans M106 P0 S0.8 I0 F200 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S0.8 I0 F200 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P2 S0.8 I0 F200 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P3 S0.8 I0 F200 H-1 ; Set fan 3 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P4 S0.8 I0 F200 H-1 ; Set fan 4 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P5 S0.8 I0 F200 H-1 ; Set fan 5 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P6 S1.0 I0 L0 F200 H-1 ; Set fan 6 value, PWM signal inversion and frequency. Thermostatic control is turned off ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Umschalten Ausgänge M307 H0 A-1 C-1 D-1 M307 H1 A-1 C-1 D-1 M307 H2 A-1 C-1 D-1 M307 H3 A-1 C-1 D-1 M307 H4 A-1 C-1 D-1 M307 H5 A-1 C-1 D-1 M307 H6 A-1 C-1 D-1 M307 H7 A-1 C-1 D-1 ; Automatic saving after power loss is not enabled ; Custom settings are not configured