; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool on Thu Aug 09 2018 00:28:17 GMT+0200 (Mitteleuropäische Sommerzeit) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 PEnder 3 ; Set machine name M552 S1 ; Enable network M587 ; M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S0 ; Drive 0 goes backwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes backwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation ; X 20.0 ; Y 20.12 ; Z 20.20 ; Y 20/20,12 * 80 = 79.522862 ; Z 20/20,20 * 400 = 396.039603 ;M92 X80 Y79.522862 Z396.039603 E140 ; Set steps per mm M92 X80 Y80 Z400 E140 ; Set steps per mm M566 X1200.00 Y1200.00 Z24.00 E300.00 ; Set maximum instantaneous speed changes (mm/min) M203 X30000.00 Y30000.00 Z300.00 E3600.00 ; Set maximum speeds (mm/min) M201 X800.00 Y800.00 Z100.00 E5000.00 ; Set accelerations (mm/s^2) M906 X800 Y800 Z800 E900 I30 ; Set motor currents (mA) and motor idle factor in per cent //E1200 M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z-1 S1 ; Set axis minima M208 X220 Y220 Z250 S0 ; Set axis maxima ; Endstops M574 X1 Y1 S1 ; Set active high endstops ; Z-Probe M574 Z1 S2 ; Set endstops controlled by probe M558 P5 H1 F120 T6000 ; Set Z probe type to switch and the dive height + speeds G31 P500 X-42 Y2 Z0.0 ; Set Z probe trigger value, offset and trigger height M557 X20:200 Y30:190 S20 ; Define mesh grid ;M376 H2 ; Define fade height; ; Heaters M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S70 ; Set temperature limit for heater 0 to 70C M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured ; Miscellaneous M501 ; Load saved parameters from non-volatile memory ; M564 H0 ; movement without homing M912 P0 S-10 ; cpu temp comp. M915 E S10 F0 R1 ; stall detection for extruder (S-value == offset, F1 == filtered, R1 == log - don't pause) M302 P1 ; allow cold extrusion ;M572 D0 S0.10 ; // linear advance