M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03+1 running on Duet Ethernet 1.02 or later + DueX5
Board ID: 08DGM-95BNL-MGPSJ-6J9F4-3SD6N-KJZMX
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93736 of which 12 recycled
Exception stack ram used: 448
Never used ram: 11196
Tasks: NETWORK(ready,524) HEAT(blocked,1236) DUEX(suspended,156) MAIN(running,360) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 01:44:44 ago, cause: software
Last software reset at 2019-07-26 23:51, reason: User, spinning module GCodes, available RAM 11368 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 46.4ms, max retries 0
MCU temperature: min 27.5, current 29.9, max 30.4
Supply voltage: min 23.9, current 24.1, max 24.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/221
Driver 1: ok, SG min/max 0/188
Driver 2: ok, SG min/max 0/1023
Driver 3: standstill, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: ok, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2019-07-27 01:36:20
Cache data hit count 4294967295
Slowest loop: 61.88ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 139, MinFreeDm: 64, MaxWait: 2608187ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 123997, completed moves: 123957, StepErrors: 0, LaErrors: 12, Underruns: 0, 0
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 F1254 X6.74800 Y29.28400 Z21.90000 E0.03318:-0.00364" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 60.86ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state 5, link 100Mbps full duplex
=== Filament sensors ===
Extruder 0 sensor: ok
Extruder 1 sensor: ok