; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2 on Wed Jul 31 2019 18:01:32 GMT-0700 (Pacific Daylight Time)

; General preferences
G90                                         ; Send absolute coordinates...
M83                                         ; ...but relative extruder moves
M665 R237.19 L494.72 B140 H267           ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0                               ; Put your endstop adjustments here, or let auto calibration find them

; Network
M550 P"My Printer"                          ; Set machine name
M551 P"none"                                ; Set password
M552 S1                                     ; Enable network
M587 S"TELUS6255" P""                       ; Configure access point. You can delete this line once connected
M586 P0 S1                                  ; Enable HTTP
M586 P1 S0                                  ; Disable FTP
M586 P2 S0                                  ; Disable Telnet

; Drives
M569 P0 S0                                  ; Physical drive 0 goes backwards
M569 P1 S0                                  ; Physical drive 1 goes backwards
M569 P2 S0                                  ; Physical drive 2 goes backwards
M569 P3 S1                                  ; Physical drive 3 goes forwards
M350 X16 Y16 Z16 E16 I1                     ; Configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E378.00            ; Set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00    ; Set maximum instantaneous speed changes (mm/min)
M203 X1800 Y1800 Z1800 E2700.00 ; Set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00    ; Set accelerations (mm/s^2)
M906 X1000.00 Y1000.00 Z1000.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                     ; Set idle timeout

; Axis Limits
M208 Z0 S1                                  ; Set minimum Z

; Endstops
M574 X2 Y2 Z2 S1                            ; Set active high endstops

; Z-Probe
M558 P5 R0.4 H0 F1200 T18000               ; Set Z probe type to effector and the dive height + speeds
G31 P500 X0 Y0 Z0                         ; Set Z probe trigger value, offset and trigger height
M557 R135 S20                               ; Define mesh grid

; Heaters
M307 H0 B0 S1.00                            ; Disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R4700                 ; Set thermistor + ADC parameters for heater 0
M143 H0 S120                                ; Set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700                 ; Set thermistor + ADC parameters for heater 1
M143 H1 S280                                ; Set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0.25 I0 F500 H T45                 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S0.25 I0 F500 H1 T45                ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P1 S"hotend" D0 H1                     ; Define tool 1
G10 P1 X0 Y0 Z0                             ; Set tool 1 axis offsets
G10 P1 R0 S0                                ; Set initial tool 1 active and standby temperatures to 0C

; Automatic saving after power loss is not enabled

; Custom settings are not configured

; Miscellaneous
M501                                        ; Load saved parameters from non-volatile memory
T1                                          ; Select first tool