; Configuration file for Duet Maestro (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.0.3 on Wed Sep 11 2019 03:28:33 GMT-0700 (Pacific Daylight Time)

; General preferences
G90                                                ; send absolute coordinates...
M83                                                ; ...but relative extruder moves
M550 P"Ender 3"                                    ; set printer name

; Network
M551 P"5KY^b6so@JG7"                               ; set password
M552 P192.168.1.24 S1                                   ; enable network and acquire dynamic address via DHCP
M586 P0 S1                                         ; enable HTTP
M586 P1 S0                                         ; disable FTP
M586 P2 S0                                         ; disable Telnet

; Drives
M569 P0 S0                                         ; physical drive 0 goes backwards
M569 P1 S0                                         ; physical drive 1 goes backwards
M569 P2 S1                                         ; physical drive 2 goes forwards
M569 P3 S0                                         ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3                                   ; set drive mapping
M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E98.00                   ; set steps per mm
M566 X600.00 Y600.00 Z60.00 E300.00                ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z600.00 E6000.00            ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z120.00 E5000.00              ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E900 I30                       ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                                   ; set axis minima
M208 X235 Y235 Z260 S0                             ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S1                                   ; set active high endstops

; Z-Probe
M558 P0 H5 F120 T6000                              ; disable Z probe but set dive height, probe speed and travel speed
M557 X10:220 Y10:220 S20                           ; define mesh grid

; Heaters
M305 P0 T98801 B4185 R2200                         ; set thermistor + ADC parameters for heater 0
M143 H0 S120                                       ; set temperature limit for heater 0 to 120C
M305 P1 T98801 B4185 R2200                         ; set thermistor + ADC parameters for heater 1
M143 H1 S250                                       ; set temperature limit for heater 1 to 250C

; Fans
M106 P0 S0 I0 F500 H-1                             ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F20 H1 T45                          ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 I0 F20 H1:0 T45                        ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 S"Hotend" D0 H1 F0                         ; define tool 0
G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                               ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0                                                 ; select first tool
M501