s; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Sat Apr 06 2019 15:41:50 GMT+0100 (British Summer Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 P"Extrudinator" ; Set machine name M552 S1 ; Enable network ;M552 S2 ;ENABLE AP MODE M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S0 ; Drive 0 goes forwards M569 P1 S0 ; Drive 1 goes forwards M569 P2 S1 ; Drive 2 goes backwards M569 P3 S0 ; Drive 3 goes backwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80.00 Y80.00 Z400.00 E669 ; Set steps per mm M566 X900.00 Y900.00 Z12.00 E120.00 ; Set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z1200.00 E1200.00 ; Set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00 ; Set accelerations (mm/s^2) M906 X1400.00 Y1400.00 Z1400.00 E800.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-27 Y-26 Z0 S1 ; Set axis minima M208 X303 Y324 Z385 S0 ; Set axis maxima ; Endstops ;M5740 X2 Y1 Z1 S1 ; Set active high endstops (inductive setup) M574 X2 Y1 S1 M574 Z1 S2 ; Z-Probe ;----------INDUCTIVE PROBE SETTINGS------- ;M558 P5 X0 Y0 Z1 H5 F120 T6000 I1 ; Disable Z probe but set dive height, probe speed and travel speed ;M557 X20:280 Y20:280 S28 ; Define mesh grid ;G31 P500 X0 Y-38.2 Z1.311 ;---------BL TOUCH SETTINGS--------------- M307 H3 A-1 C-1 D-1 ;Heater 3 pin is being used for the BL touch so this is disabling it M558 P9 H5 F100 T2000 G31 P25 X0 Y-38.2 Z0 ; Heaters M307 H0 B0 S1.00 ; Disable bang-bang mode for the bed heater and set PWM limit M305 P0 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C ;M301 H1 P15.67 I0.60 D102.06 ;Dyze PID Values suggested M305 P1 T4606017 B5848 C5.548428e-8 R4700 H0 L0 ;M305 P1 T100000 B4138 R4700 ; Set thermistor + ADC parameters for heater 1 M307 H1 A580.4 C256.6 D6.4 S0.50 M143 H1 S493 ; Set temperature limit for heater 1 to 493C ; Fans M106 P1 S1 I0 F500 H1 T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured ;Load Mesh Bed Compensation file G29 S1 ;Load config override M501