11/21/2019, 9:47:00 PM: Connected to 192.168.0.81
11/21/2019, 9:47:09 PM: Upload of Part Cooling - Nozzle v2 - Left & Right.gcode successful after 2s
11/21/2019, 9:47:09 PM: M32 "0:/gcodes/Part Cooling - Nozzle v2 - Left & Right.gcode": File 0:/gcodes/Part Cooling - Nozzle v2 - Left & Right.gcode selected for printing
11/21/2019, 10:22:21 PM: : Finished printing file 0:/gcodes/Part Cooling - Nozzle v2 - Left & Right.gcode, print time was 0h 35m
11/21/2019, 11:04:10 PM: Upload of ALL Reel Mount - Arm - Surface - L.gcode successful after 5s
11/21/2019, 11:04:11 PM: M32 "0:/gcodes/ALL Reel Mount - Arm - Surface - L.gcode": File 0:/gcodes/ALL Reel Mount - Arm - Surface - L.gcode selected for printing
11/22/2019, 1:21:59 AM: Connection interrupted, attempting to reconnect...: Network error
11/22/2019, 1:22:22 AM: Connection established
11/22/2019, 1:23:49 AM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.04 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DDM-9FAM2-LW4SD-6JTD6-3S86L-1LWRX
Used output buffers: 4 of 24 (7 max)
=== RTOS ===
Static ram: 25680
Dynamic ram: 93608 of which 0 recycled
Exception stack ram used: 268
Never used ram: 11516
Tasks: NETWORK(ready,676) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,3816) IDLE(ready,200)
Owned mutexes:
=== Platform ===
Last reset 00:01:45 ago, cause: software
Last software reset at 2019-11-22 01:21, reason: Stuck in spin loop, spinning module GCodes, available RAM 11044 bytes (slot 0)
Software reset code 0x4043 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f80f BFAR 0xe000ed38 SP 0x2000323c Task 0x454c4449
Stack: 004450f5 00444214 61000000 a5a5a5a5 20003258 200030f8 00000002 200048d4 03c441a3 2000177c 20004ce4 20003258 20004cdc 00000004 20001790 200030d0 20003258 200030c8 00000001 200032b0 4e49414d 00000000 00000000
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 12.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 32.6, current 33.7, max 34.3
Supply voltage: min 12.0, current 12.0, max 12.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max not available
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2019-11-22 01:23:48
Cache data hit count 364665100
Slowest loop: 11.87ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 39.51ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 5c:cf:7f:ef:4d:b7
WiFi Vcc 3.37, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 22576
WiFi IP address 192.168.0.81
WiFi signal strength -52dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0