; Configuration file for Duet Maestro (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.3 on Tue Nov 26 2019 20:35:08 GMT+0100 (Mitteleuropäische Normalzeit)

; General preferences
G90                                        ; send absolute coordinates...
M83                                        ; ...but relative extruder moves
M550 P"HEvo"      			               ; set printer name

; Network
M551 P"reprap"                             ; set password
M552 P192.168.4.120 S1                     ; enable network and acquire dynamic address via DHCP
M586 P0 S1                                 ; enable HTTP
M586 P1 S0                                 ; disable FTP
M586 P2 S0                                 ; disable Telnet

; Drives
M569 P0 S1                                 ; physical drive 0 goes forwards
M569 P1 S1                                 ; physical drive 1 goes forwards
M569 P2 S1                                 ; physical drive 2 goes forwards
M569 P3 S1                                 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                           ; set drive mapping
M350 X16 Y16 Z16 E16 I1                    ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E415.00         ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00        ; set maximum instantaneous speed changes (mm/min)
M203 X7200.00 Y7200.00 Z180.00 E1200.00    ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z20.00 E250.00      ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30               ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                    ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                           ; set axis minima
M208 X220 Y220 Z200 S0                     ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S1                           ; set active high endstops

; Z-Probe
M558 P0 H5 F120 T6000                      ; disable Z probe but set dive height, probe speed and travel speed
M557 X20:180 Y20:180 S20                   ; define mesh grid

; Heaters
M305 P0 T100000 B4100 R2200                ; set thermistor + ADC parameters for heater 0
M143 H0 S105                               ; set temperature limit for heater 0 to 105C
M305 P1 T100000 B4100 R2200                ; set thermistor + ADC parameters for heater 1
M143 H1 S280                               ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 C"Part Cooling Fan" S0 I0 F500 H-1 ; set fan 0 name, value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 C"Coolend Fan" S0 I0 F500 H1 T50   ; set fan 1 name, value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 S"Hotend 0" D0 H1 F0               ; define tool 0
G10 P0 X0 Y0 Z0                            ; set tool 0 axis offsets
G10 P0 R0 S0                               ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
T0                                         ; select first tool