; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Tue Dec 04 2018 15:25:11 GMT-0500 (Eastern Standard Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M667 S1 ; Select CoreXY mode ; Network M550 P"GenTec CorXY" ; Set machine name M551 P"sc00ter1" ; Set password M552 S1 ; Enable network M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S1 ; Drive 0 goes forwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S1 ; Drive 3 goes forwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X100.00 Y100.00 Z1500.00 E402.4 ; Set steps per mm M566 X1200.00 Y1200.00 Z700.00 E3000.00 ; Set maximum instantaneous speed changes (mm/min) M203 X10000.00 Y10000.00 Z1500.00 E1200.00 ; Set maximum speeds (mm/min) M201 X800.00 Y800.00 Z20.00 E1200.00 ; Set accelerations (mm/s^2) M906 X1000.00 Y1000.00 Z1000.00 E1400.00 I30;Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-140 Y-80 Z0 S1 ; Set axis minima M208 X150 Y102 Z200 S0 ; Set axis maxima ; Endstops M574 X1 Y2 S0 ; Set active low endstops Z1 M574 Z1 S2 ; Define Z to use Probe. Home to Min ; Z-Probe M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board M558 P9 H5 F300 T4000 X0 Y0 Z1 ; Set Z probe type/mode 5. H=Dive Height. F=Speed the bed moves From Site G31 P500 X-29.44 Y10.0 Z2.36 ; Set Z probe trigger value, offset and trigger height M557 X-100:150 Y-70:80 S10 ; Define mesh grid ; Heaters M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning) M305 P0 T100000 B3950 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4388 C7.060000e-8 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S300 ; Set temperature limit for heater 1 to 300C ; Fans M106 P0 T45 H1 ; Set fan 0 value, Thermostatic control is turned on M106 P1 H-1 ; Set fan 1 value, Thermostatic control is turned off M106 P2 H-1 ; Set fan 2 value, Thermostatic control is turned off ; Tools M563 P0 D0 H1 F1 ; tool 0 uses extruder 0, heater 1 (and fan 1) G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured ; Miscellaneous M501 ; Load Defaults M80 ; Turn On Power Supply T0 ; Select first tool M106 P1 S0 ; Turn off cooling fan