; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Tue Feb 26 2019 21:31:01 GMT+0000 (Greenwich Mean Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Delta Settings M665 L440.40:440.42:440.41 R226.821 H410.00 B185.0 X0.00 y-0.00 z0 ; Set delta radius, diagonal rod length, M666 X0 y0 z0 A0.00 B0.00 ; Put your endstop adjustments here, or let auto calibration find them ; Network M550 P"Anycubic Predator" ; Set machine name M551 P"141081" ; Set password M552 S1 ; Enable network and acquire dynamic address via DHCP M553 P255.255.255.0 M554 P192.168.1.117 M586 P0 S1 ; Enable HTTP M586 P1 S1 ; Disable FTP M586 P2 S1 ; Disable Telnet ; Drives M569 P0 S1 ; Drive 0 goes forwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes forwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X160.00 Y160.00 Z160.00 E410.35 ; Set steps per mm M566 X1000 Y1000 Z1000 E1000 ; Set maximum instantaneous speed changes (mm/min) M203 X12000.00 Y12000.00 Z12000.00 E12000 ; Set maximum speeds (mm/min) M201 X3000.00 Y3000.00 Z3000.00 E3000 ; Set accelerations (mm/s^2) M906 X1800.00 Y1800.00 Z1800.00 E700.00 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Retraction ;M207 S2.3 F7000 R0.0 T2500 Z0.0 ; Firmware retraction ; Axis Limits M208 Z0 S1 ; Set minimum Z ; Endstops M574 X2 Y2 Z2 S1 ; Set active high endstops ; Z-Probe M558 P8 R0.4 F800 H3 T5000 ; Set Z probe type to switch and the dive height + speeds G31 P100 X0 Y0 Z-0.1 ; Set Z probe trigger value, offset and trigger height M557 R175 S20 ; Define mesh grid ; Heaters M307 H0 A137.8 C533.3 D1.5 V24.3 B0 ; Disable bang-bang mode for the bed heater and set PWM limit M305 P0 T100000 B4300 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4725 C7.06e-8 ; Set thermistor + ADC parameters for heater 1 M143 H1 S290 ; Set temperature limit for heater 1 to 240C M307 H2 A-1 C-1 D-1 ; Disconnect H2 from being a heater - LED ; Fans M106 P0 S0 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured ;M572 D0 S0.1 ; Pressure Advance M591 D0 P1 C4 S1 ; Activate filament sensor M404 N1.75 ; Set for print monitor ;M579 X0.9955 Y0.9955 Z0.993 M592 D0 A0.015 B0.0012 L0.2 ; Nonlinear extrusion. Set parameters for extruder drive 0 - 0.4mm M575 P1 B57600 S1 ; Miscellaneous M501 ; Load saved parameters from non-volatile memory