2/8/2020, 2:14:37 PM: Connected to 192.168.0.133
2/8/2020, 2:16:19 PM: Upload of config.g successful after 0s
2/8/2020, 2:20:18 PM: M120
G91
G1 Z5 F6000
G90
M121: Error: G0/G1: insufficient axes homed
2/8/2020, 2:20:29 PM: M120
G91
G1 Z-5 F6000
G90
M121: Error: G0/G1: insufficient axes homed
2/8/2020, 2:21:03 PM: Connection interrupted, attempting to reconnect...: Network error
2/8/2020, 2:55:17 PM: Connection established
2/8/2020, 2:59:36 PM: Connection interrupted, attempting to reconnect...: Network error
2/8/2020, 3:01:16 PM: Connection established
2/8/2020, 3:02:01 PM: M98 P"0:/macros/03-Test_Heaters": Error: M570: Heater 2 not found
Error: M563: Tool creation: bad drive number
Error: G10: Attempt to set/report offsets and temperatures for non-existent tool: 2
2/8/2020, 3:02:11 PM: : Error: G10: Attempt to set/report offsets and temperatures for non-existent tool: 2
2/8/2020, 3:02:40 PM: M98 P"0:/macros/04-Test_motors": Error: GCodes: Attempt to read a GCode float array that is too long: M906 X2000 Y2000 Z2000 E2000:2000 I100 
Error: GCodes: Attempt to read a GCode unsigned array that is too long: M350 X16 Y16 Z16 E16:16 I0			
Error: GCodes: Attempt to read a GCode float array that is too long: M92 X80 Y80 Z80	E80:80				
Error: GCodes: Attempt to read a GCode float array that is too long: M906 X2000 Y2000 Z2000 E2000:2000 I100 		
Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
2/8/2020, 3:02:41 PM: : Warning: motor phase A may be disconnected reported by driver(s) 2
Warning: motor phase B may be disconnected reported by driver(s) 2
2/8/2020, 3:02:42 PM: : Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
2/8/2020, 3:02:45 PM: : Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
2/8/2020, 3:02:46 PM: : Warning: motor phase A may be disconnected reported by driver(s) 2
Warning: motor phase B may be disconnected reported by driver(s) 2
2/8/2020, 3:02:47 PM: : Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
2/8/2020, 3:02:50 PM: : Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
2/8/2020, 3:02:51 PM: : Warning: motor phase A may be disconnected reported by driver(s) 2
Warning: motor phase B may be disconnected reported by driver(s) 2
2/8/2020, 3:02:52 PM: : Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
2/8/2020, 3:02:55 PM: : Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
2/8/2020, 3:02:56 PM: : Warning: motor phase A may be disconnected reported by driver(s) 2
Warning: motor phase B may be disconnected reported by driver(s) 2
2/8/2020, 3:02:56 PM: Emergency stop, attemping to reconnect...
2/8/2020, 3:03:08 PM: Connection established