; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Feb 11 2020 13:59:00 GMT-0500 (Eastern Standard Time)

; General preferences
G90                                           ; send absolute coordinates...
M83                                           ; ...but relative extruder moves
M550 P"Blaise's Printer"                      ; set printer name

; Network
M551 P"Teddy2018"                             ; set password
M552 S1                                       ; enable network
M552 P169.254.187.249                         ; set IP address (BLT)
M586 P0 S1                                    ; enable HTTP
M586 P1 S0                                    ; disable FTP
M586 P2 S0                                    ; disable Telnet

; Drives
M569 P0 S0                                    ; physical drive 0 goes backwards (BLT)
M569 P1 S0                                    ; physical drive 1 goes backwards
M569 P2 S0                                    ; physical drive 2 goes backwards
M569 P3 S1                                    ; physical drive 3 goes forwards 
M584 X0 Y1 Z2 E3                              ; set drive mapping
M350 X16 Y16 Z16 E16 I1                       ; configure microstepping with interpolation
M92 X35.83 Y56.30 Z5.09 E873.08               ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00           ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00       ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00           ; set accelerations (mm/s^2)
M906 X2000 Y950 Z800 E1400 I30                ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                       ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                              ; set axis minima
M208 X630 Y240 Z170 S0                        ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                           ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                           ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S2                                    ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"exp.heater3"                        ; create servo pin 0 for BLTouch
M558 P9 H3 F500 T4000            ; F120 T6000 set Z probe type to bltouch and the dive height + speeds
G31 P25 X-20 Y32 Z0                        ; Z was 2.5 set Z probe trigger value, offset and trigger height
M557 X15:215 Y15:195 S20                      ; define mesh grid

; Heaters
M140 H-1                                      ; disable heated bed (overrides default heater mapping)
M308 S0 P"e0temp" Y"thermistor" T115000 B4138 ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"e0heat" T0                          ; create nozzle heater output on e0heat and map it to sensor 0
M143 H0 S280                                  ; set temperature limit for heater 0 to 280C
M307 H0 B0 S1.00                              ; disable bang-bang mode for heater  and set PWM limit
M307 H3 A-1 C-1 D-1 ; Disable the 3rd Heater to free up PWM channel ; Fans
M950 F0 C"fan0" Q500                          ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1                                ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                          ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1                                ; set fan 1 value. Thermostatic control is turned off

; Tools
M563 P0 S"Extruder 0" D0 H1 F0                ; define tool 0
G10 P0 X0 Y0 Z0                               ; set tool 0 axis offsets
G10 P0 R0 S0                                  ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined