2/29/2020, 1:40:59 PM: Connected to 192.168.0.133
2/29/2020, 1:42:58 PM: Upload of homex.g successful after 0s
2/29/2020, 2:05:20 PM: Upload of config.g successful after 0s
2/29/2020, 2:05:32 PM: Connection interrupted, attempting to reconnect...: Network error
2/29/2020, 2:05:34 PM: Connection established
2/29/2020, 2:18:57 PM: M303 P0.9 S230: No heater has been tuned yet
2/29/2020, 2:19:21 PM: M303 H1 P0.9 S230: Auto tuning heater 1 using target temperature 230.0°C and PWM 0.90 - do not leave printer unattended
2/29/2020, 2:19:27 PM: : Auto tune phase 1, heater on
2/29/2020, 2:21:39 PM: : Auto tune phase 2, heater off
2/29/2020, 2:21:45 PM: : Auto tune phase 3, peak temperature was 234.9
2/29/2020, 2:24:21 PM: : Auto tune heater 1 completed in 300 sec
Use M307 H1 to see the result, or M500 to save the result in config-override.g
2/29/2020, 2:24:46 PM: M307 H1: Heater 1 model: gain 400.9, time constant 168.7, dead time 5.1, max PWM 0.90, calibration voltage 23.9, mode PID
Computed PID parameters for setpoint change: P14.8, I0.504, D52.6
Computed PID parameters for load change: P14.8, I1.061, D52.6
2/29/2020, 2:25:21 PM: M500: Warning: No M501 command was executed in config.g
2/29/2020, 2:26:47 PM: M303 H0 P0.5 S80: Auto tuning heater 0 using target temperature 80.0°C and PWM 0.50 - do not leave printer unattended
2/29/2020, 2:26:53 PM: : Auto tune phase 1, heater on
2/29/2020, 2:31:45 PM: : Auto tune phase 2, heater off
2/29/2020, 2:31:49 PM: : Auto tune phase 3, peak temperature was 80.3
2/29/2020, 2:38:57 PM: : Auto tune heater 0 completed in 729 sec
Use M307 H0 to see the result, or M500 to save the result in config-override.g
2/29/2020, 2:39:37 PM: M307 H0: Heater 0 model: gain 129.5, time constant 465.2, dead time 0.9, max PWM 0.50, calibration voltage 23.7, mode PID
Computed PID parameters for setpoint change: P752.9, I37.817, D449.0
Computed PID parameters for load change: P752.9, I160.363, D449.0
2/29/2020, 2:39:49 PM: M500: Warning: No M501 command was executed in config.g
2/29/2020, 2:53:39 PM: Upload of config.g successful after 0s
2/29/2020, 2:53:51 PM: Connection interrupted, attempting to reconnect...: Network error
2/29/2020, 2:53:53 PM: Connection established
2/29/2020, 2:55:06 PM: Emergency stop, attemping to reconnect...
2/29/2020, 2:55:06 PM: G28 Z: Error: Homing failed
2/29/2020, 2:55:06 PM: M112
M999: Error: Homing failed
2/29/2020, 2:55:17 PM: Connection established
2/29/2020, 2:56:17 PM: Upload of homez.g successful after 0s
2/29/2020, 2:58:50 PM: M115: FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.0 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-01-03b3
2/29/2020, 2:59:00 PM: M119: Endstops - X: at min stop, Y: at max stop, Z: at min stop, Z probe: at min stop