; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Tue Oct 09 2018 13:27:56 GMT+0300

; General preferences
M80				; Turns on the ATX power supply
G90                                                ; Send absolute coordinates...
M83                                                ; ...but relative extruder moves

M667 S1                                            ; Select CoreXY mode

; Network
M550 PBLV mgn Cube                                 ; Set machine name
M552 S1                                            ; Enable network
M587 S"FDMDEV" P"XXXXXXXXXXXXXXXXXXXXX"            ; Configure access point. You can delete this line once connected
M586 P0 S1                                         ; Enable HTTP
M586 P1 S0                                         ; Disable FTP
M586 P2 S0                                         ; Disable Telnet

; Drives
M569 P0 S0                                         ; Drive 0 goes backwards blv: its was S1
M569 P1 S0                                         ; Drive 1 goes backwards blv: its was S1
M569 P2 S1                                         ; Drive 2 goes forwards
M569 P3 S0                                         ; Drive 3 goes backwards WAS 0
M569 P4 S0                                         ; Drive 3 goes backwards WAS 0

M350 X16 Y16 Z16:16 U16 E16 I1                     ; Configure microstepping with interpolation
M92 X200 Y200 Z800 U800 E405.18                    ; Set steps per mm for Bondtech. 
M566 X600 Y600 Z24 U24 E300                        ; Set maximum instantaneous speed changes (Jerk) (mm/min) 
M203 X20000 Y20000 Z600 U600 E2000                 ; Set maximum speeds (mm/min) 
M201 X3000 Y3000 Z100 U100 E5000	           ; Set accelerations (mm/s^2)
M906 X1600 Y1600 Z1600 U1600 E1600 I30             ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Pressure advance
; M572 D0 S0.05					   ; disabled Pressure advance

; Axis Limits
M208 X-23 Y0 Z0 S1                                 ; Set axis minima
M208 X310 Y311 Z480 S0                             ; Set axis maxima

; Endstops
M574 X1 Y2 Z1 U1 S1                                 ; Set active high endstops edit: Y endstop is high(max).

; Filament sensor
M591 D0 P1 C3 S1				   ; Set Filament sensor Simple type (High) for extruder drive 0, connected to endstop input 3 (E0)

; Z-Probe
M574 Z1 S2                                         ; Set endstops controlled by probe
M307 H1 A372.3 C109.6 D4.6 B0			   ; Set PID for hotend values
M307 H0 A99.1 C453.2 D2.2 B0			   ; Set PID for heated bed values
M558 P1 H5 F200 T10000 I0 R0.5			   ; Set Z probe type mini ir sensor
G31 P500 X-2 Y-16.4 Z0.880                         ; Set Z probe trigger value, offset and trigger height
M557 X30:270 Y30:270 S80		       	; Define mesh grid

; Heaters
M305 P0 T100000 B3950 C0 R4700                     ; Set thermistor + ADC parameters for heater 0
M143 H0 S100                                       ; Set temperature limit for heater 0 to 100C
M305 P1 T100000 B3950 C0 R4700                     ; Set thermistor + ADC parameters for heater 1
M143 H1 S260                                       ; Set temperature limit for heater 1 to 260C

; Fans
M106 P0 S0 I0 F500 H-1                             ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T35                          ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T35                          ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                                      ; Define tool 0
G10 P0 X0 Y0 Z0                                    ; Set tool 0 axis offsets
G10 P0 R0 S0                                       ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S21 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured
M564 H0                                   	   ; Let the Jog buttons work blv: added to allow jog buttons

; Motor remapping for dual Z
M584 X0 Y1 Z2:4 U4 E3 P3 ; Driver 0 For X, 1 for Y, Z=2:4 U=4, Extruder 3