; Configuration file for Duet WiFi (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Tue Oct 09 2018 13:27:56 GMT+0300

; General preferences
M80				; Turns on the ATX power supply
G90                                                ; Send absolute coordinates...
M83                                                ; ...but relative extruder moves
M667 S1                                            ; Select CoreXY mode

; Network
M550 Lethe's Cube                                 ; Set machine name
M552 S1                                            ; Enable network
M587 S"PurpleTrouble" P"VFmy86aB"            ; Configure access point. You can delete this line once connected
M586 P0 S1                                         ; Enable HTTP
M586 P1 S0                                         ; Disable FTP
M586 P2 S0                                         ; Disable Telnet

; Drives
M569 P0 S0                                         ; Drive 0 goes backwards blv: its was S1
M569 P1 S0                                         ; Drive 1 goes backwards blv: its was S1
M569 P2 S0                                         ; Drive 2 goes forwards
M569 P3 S0                                         ; Drive 3 goes backwards WAS 0
M350 X16 Y16 Z16 E16 I1                            ; Configure microstepping with interpolation
M92 X200 Y200 Z400 E424.3                         ; Set steps per mm for Bondtech. 
M566 X600 Y600 Z24 E300                            ; Set maximum instantaneous speed changes (Jerk) (mm/min) 
M203 X20000 Y20000 Z600 E2000                      ; Set maximum speeds (mm/min) 
M201 X3000 Y3000 Z100 E5000			   				 ; Set accelerations (mm/s^2)
M906 X1600 Y1600 Z1600 E1600 I30                   ; Set motor currents (mA) and motor idle factor in per cent
M84 S30                                            ; Set idle timeout

; Pressure advance
M572 D0 S0.05					   					; disabled Pressure advance

; Axis Limits
M208 X-18 Y25 Z0 S1                               ; set axis minima
M208 X300 Y300 Z665 S0                            ; set axis maxima

; Endstops
M574 X1 Y1 S0                                     ; set active low and disabled endstops
M574 Z1 S2                                        ; set endstops controlled by probe

; Filament sensor
M591 D0 P0 C3 S1				 					  ; Set Filament sensor Simple type (High) for extruder drive 0, connected to endstop input 3 (E0)

; Z-Probe
M307 H3 A-1 C-1 D-1                               ; disable heater on PWM channel for BLTouch
M307 H1 A404.7 C130.4 D5.7 V23.7 B0			  		 ; Set PID for hotend values gain
M307 H0 A99.1 C453.2 D2.2 B0						  ; Set PID for heated bed values
M558 P9 H5 F120 T6000                             ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-2 Y-16.4 Z2.5                          ; set Z probe trigger value, offset and trigger height
M557 X-30:275 Y30:270 S80                          ; define mesh grid

; Heaters
M305 P0 T100000 B4267 C7.06e-8 R4700                     ; Set thermistor + ADC parameters for heater 0
M143 H0 S125                                       ; Set temperature limit for heater 0 to 100C
M305 P1 T100000 B3950 C0 R4700                     ; Set thermistor + ADC parameters for heater 1
M143 H1 S270                                       ; Set temperature limit for heater 1 to 260C

; Fans
M106 P0 S0 I0 F500 H-1                             ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T35                          ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1 T35                          ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1                                      ; Define tool 0
G10 P0 X0 Y0 Z0                                    ; Set tool 0 axis offsets
G10 P0 R0 S0                                       ; Set initial tool 0 active and standby temperatures to 0C

; Automatic power saving
M911 S21 R22 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Set voltage thresholds and actions to run on power loss

; Custom settings are not configured
M564 H0                                   	   ; Let the Jog buttons work blv: added to allow jog buttons