; Configuration file for Duet Maestro (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Feb 18 2020 18:08:43 GMT-0500 (Eastern Standard Time)

; General preferences
G90                                        ; send absolute coordinates...
M83                                        ; ...but relative extruder moves
M550 P"Ender5Pro - 3DimensionGames"          ; set printer name
M564 H0					   ;allow movement without homing

; Network
M552 P0.0.0.0 S1                           ; enable network and acquire dynamic address via DHCP
M586 P0 S1                                 ; enable HTTP
M586 P1 S0                                 ; disable FTP
M586 P2 S0                                 ; disable Telnet

; Drives
M569 P0 S1                                 ; physical drive 0 goes forwards
M569 P1 S1                                 ; physical drive 1 goes forwards
M569 P2 S0                                 ; physical drive 2 goes backwards
M569 P3 S0                                 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                           ; set drive mapping
M350 X16 Y16 Z16 E16 I1                    ; configure microstepping with interpolation
M92 X80.15 Y79.04 Z800 E410        	; set steps per mm
M566 X900 Y900 Z30 E300	   		   ; set jerk (mm/min)
M203 X7200 Y7200 Z600 E6000 		   ; set maximum speeds (mm/min)
M201 X1200.00 Y1200.00 Z240.00 E5000.00    ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z800 E1000 I50              ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                    ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                           ; set axis minima
M208 X235 Y235 Z260 S0                     ; set axis maxima

; Endstops
M574 X0 Y1 S1                              ; set active high endstops
M574 Z1 S2                                 ; set endstops controlled by probe

; Z-Probe
M558 P9 H2 F90 T24000                    ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X41 Y24 Z0.87		; set Z probe trigger value, offset and trigger height
M557 X45:225 Y30:210 S45                   ; define mesh grid

; Heaters
M307 H0 B0 S1.00                           ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B3950 R2200                ; set thermistor + ADC parameters for heater 0
M143 H0 S150                               ; set temperature limit for heater 0 to 150C
M305 P1 T100000 B3950 R2200                ; set thermistor + ADC parameters for heater 1
M143 H1 S275                               ; set temperature limit for heater 1 to 275C

; Fans
M106 P0 S0 I0 F500 H-1                     ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                  ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S1 I0 F500 H1:0 T45                ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                           ; define tool 0
G10 P0 X0 Y0 Z0                            ; set tool 0 axis offsets
G10 P0 R0 S0                               ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined
M501
G29 S1
M572 D0 S0.18; set K value for pressure advance