3/28/2020, 4:00:10 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-917NK-F2MS4-7J1F0-3S46R-KGS4D
Used output buffers: 3 of 24 (14 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 94064 of which 0 recycled
Exception stack ram used: 544
Never used ram: 10752
Tasks: NETWORK(ready,628) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,1664) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 02:20:48 ago, cause: software
Last software reset at 2020-03-28 13:39, reason: User, spinning module GCodes, available RAM 10776 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 8
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 37.8ms, max retries 0
MCU temperature: min 30.4, current 36.0, max 36.4
Supply voltage: min 24.0, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/1023
Driver 1: ok, SG min/max 0/1023
Driver 2: standstill, SG min/max 43/223
Driver 3: standstill, SG min/max 49/235
Driver 4: standstill, SG min/max 0/219
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max 0/1023
Driver 7: ok, SG min/max 0/1023
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-03-28 16:00:05
Cache data hit count 4294967295
Slowest loop: 127.93ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 157, MinFreeDm: 143, MaxWait: 359152ms
Bed compensation in use: mesh, comp offset 0.000
=== DDARing ===
Scheduled moves: 1498, completed moves: 1487, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 2 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X158.286 Y150.786 E0.19495" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 39.24ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 60:01:94:2e:9f:97
WiFi Vcc 3.38, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25856
WiFi IP address 192.168.0.81
WiFi signal strength -59dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
3/28/2020, 4:01:22 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-917NK-F2MS4-7J1F0-3S46R-KGS4D
Used output buffers: 1 of 24 (17 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 94064 of which 0 recycled
Exception stack ram used: 544
Never used ram: 10752
Tasks: NETWORK(ready,628) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,1664) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 02:22:00 ago, cause: software
Last software reset at 2020-03-28 13:39, reason: User, spinning module GCodes, available RAM 10776 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 8
Free file entries: 7
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 35.9, current 36.6, max 36.7
Supply voltage: min 24.0, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/1023
Driver 1: ok, SG min/max 0/1023
Driver 2: ok, SG min/max 62/189
Driver 3: ok, SG min/max 58/200
Driver 4: ok, SG min/max 0/178
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max 0/1023
Driver 7: standstill, SG min/max 0/525
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-03-28 16:01:17
Cache data hit count 4294967295
Slowest loop: 5.12ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 154, MinFreeDm: 150, MaxWait: 19ms
Bed compensation in use: mesh, comp offset 0.000
=== DDARing ===
Scheduled moves: 1927, completed moves: 1912, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.1
Heater 1 is on, I-accum = 0.8
=== GCodes ===
Segments left: 0
Stack records: 3 allocated, 2 in use
Movement lock held by file
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 1 0 10
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.18ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 1
WiFi firmware version 1.23
WiFi MAC address 60:01:94:2e:9f:97
WiFi Vcc 3.39, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25856
WiFi IP address 192.168.0.81
WiFi signal strength -60dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
3/28/2020, 4:01:42 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-917NK-F2MS4-7J1F0-3S46R-KGS4D
Used output buffers: 1 of 24 (22 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 94064 of which 0 recycled
Exception stack ram used: 544
Never used ram: 10752
Tasks: NETWORK(ready,628) HEAT(blocked,1232) DUEX(suspended,160) MAIN(running,1664) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 02:22:20 ago, cause: software
Last software reset at 2020-03-28 13:39, reason: User, spinning module GCodes, available RAM 10776 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 8
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 36.4, current 36.7, max 36.9
Supply voltage: min 24.1, current 24.2, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/226
Driver 1: ok, SG min/max 0/230
Driver 2: ok, SG min/max 56/205
Driver 3: ok, SG min/max 64/211
Driver 4: ok, SG min/max 0/206
Driver 5: standstill, SG min/max not available
Driver 6: standstill, SG min/max not available
Driver 7: standstill, SG min/max 0/268
Driver 8: standstill, SG min/max not available
Driver 9: standstill, SG min/max not available
Date/time: 2020-03-28 16:01:37
Cache data hit count 4294967295
Slowest loop: 4.50ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 157, MinFreeDm: 151, MaxWait: 18ms
Bed compensation in use: mesh, comp offset 0.000
=== DDARing ===
Scheduled moves: 1998, completed moves: 1986, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 2 is on, I-accum = 0.4
=== GCodes ===
Segments left: 1
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 F3000.000" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 201.28ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 2 of 8
- WiFi -
Network state is running
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 2
WiFi firmware version 1.23
WiFi MAC address 60:01:94:2e:9f:97
WiFi Vcc 3.39, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25856
WiFi IP address 192.168.0.81
WiFi signal strength -60dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0