; ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M667 S1 ; Select CoreXY mode ; Network M550 PCaslte ; Set machine name M552 S1 ; Enable network ;*** Access point is configured manually via M587 M586 P0 S1 ; Enable HTTP M586 P1 S1 ; Enable FTP M586 P2 S0 ; Disable Telnet M587 S"RI-Wireless" P"Ridgeview8648" ; Drives M569 P0 S1 ; Drive 0 goes forwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S1 ; Drive 3 goes forwards M569 P4 S1 ; Drive 4 goes forwards M350 X64 Y64 Z32 E64:64 I1 ; Configure microstepping with interpolation M92 X400 Y400 Z2547.5 E1641:1641 ; Set steps per mm M566 X1200 Y1200 Z4 E120:120 ; Set maximum instantaneous speed changes (mm/min) M203 X18000 Y18000 Z1400 E1200:1200 ; Set maximum speeds (mm/min) M201 X1050 Y1050 Z180 E250:250 ; Set accelerations (mm/s^2) M906 X950 Y950 Z800 E1000:1000 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-10 Y-30 Z0 S1 ; Set axis minima M208 X355 Y345 Z750 S0 ; Set axis maxima ; Endstops M574 Z1 S2 ; set endstops controlled by probe M574 X1 Y1 S3 ; Set endstops controlled by motor load detection ; Z-Probe M307 H5 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch M558 P9 H5 F120 T4500 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X0 Y66 Z1.7 ; set Z probe trigger value, offset and trigger height M557 X10:345 Y-30:290 S45 ; define mesh grid ; Heaters M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S285 ; Set temperature limit for heater 1 to 285C ;M305 P3 T100000 B4138 C0 R4700 X2 ; Set thermistor + ADC parameters for heater 3 and remap it to channel 2 ;M143 H3 S90 ; Set temperature limit for heater 3 to 90C ; Fans ;M106 P0 S1 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on ;M106 P2 S1 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C M563 P1 D1 H1 ; Define tool 1 G10 P1 X0 Y0 Z0 ; Set tool 1 axis offsets ;G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured ; Miscellaneous M501 ; Load saved parameters from non-volatile memory T0 ; Select first tool