5/25/2020, 2:18:52 PM: Connected to 192.168.86.82
5/25/2020, 2:23:27 PM: M32 "0:/gcodes/8 Wonder Woman.gcode": File 0:/gcodes/8 Wonder Woman.gcode selected for printing
5/25/2020, 2:23:43 PM: : Resume state saved
5/25/2020, 2:23:46 PM: : Printing paused at X110.0 Y110.0 Z6.0
5/25/2020, 2:24:00 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 Maestro version 2.05.1 running on Duet Maestro 1.0
Board ID: 08DJM-956DU-LL3T0-6J1FL-3SD6Q-9926P
Used output buffers: 3 of 24 (8 max)
=== RTOS ===
Static ram: 19804
Dynamic ram: 94160 of which 0 recycled
Exception stack ram used: 328
Never used ram: 16780
Tasks: NETWORK(ready,764) HEAT(blocked,1272) MAIN(running,3896) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 02:03:46 ago, cause: power up
Last software reset at 2020-05-25 11:41, reason: User, spinning module GCodes, available RAM 16756 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0400f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 15.0MBytes/sec
SD card longest block write time: 2.4ms, max retries 0
MCU temperature: min 40.3, current 44.7, max 45.2
Supply voltage: min 0.0, current 24.0, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, read errors 0, write errors 0, ifcount 10, reads 34885, timeouts 0
Driver 1: standstill, read errors 0, write errors 0, ifcount 10, reads 34885, timeouts 0
Driver 2: standstill, read errors 0, write errors 0, ifcount 10, reads 34885, timeouts 0
Driver 3: standstill, read errors 0, write errors 0, ifcount 8, reads 34780, timeouts 107
Driver 4: standstill, read errors 0, write errors 0, ifcount 6, reads 34889, timeouts 0
Driver 5: ok, read errors 0, write errors 0, ifcount 0, reads 0, timeouts 34894
Driver 6: ok, read errors 0, write errors 0, ifcount 0, reads 0, timeouts 34894
Date/time: 2020-05-25 14:23:59
Slowest loop: 109.72ms; fastest: 0.06ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 157, MaxWait: 7247283ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 32, completed moves: 32, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
lcd is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 4.67ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state 5, link 100Mbps full duplex
=== Filament sensors ===
Extruder 0: pos 86.48, errs: frame 6 parity 0 ovrun 0 pol 0 ovdue 0