; Configuration file for Duet 3 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu Mar 12 2020 00:55:37 GMT+0100 (Mitteleuropäische Normalzeit) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"RatRig V-Core Pro" ; set printer name M669 K1 ; select CoreXY mode ; Network M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0.0 S1 ; physical drive 0.0 goes forwards Left M569 P0.1 S1 ; physical drive 0.1 goes forwards Rear M569 P0.2 S1 ; physical drive 0.2 goes forwards Right M569 P0.3 S0 ; physical drive 0.3 goes forwards X M569 P0.4 S0 ; physical drive 0.4 goes forwards Y M569 P0.5 S0 ; physical drive 0.5 goes forwards E M584 X0.3 Y0.4 Z0.2:0.0:0.1 E0.5 ; set drive mapping Z-Motors: Right, Left, Rear M350 X16 Y16 Z16 E32 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z400.00 E830.00 ; set steps per mm M566 X1800.00 Y1800.00 Z180.00 E2200.00 ; set maximum instantaneous speed changes (mm/min) - testing dyn acc M203 X12000.00 Y12000.00 Z2100.00 E12000.00 ; set maximum speeds (mm/min) - testing dyn acc M201 X10000.00 Y10000.00 Z100.00 E200.00 ; set accelerations (mm/s^2) - testing dyn acc ; M566 X900.00 Y900.00 Z180.00 E2200.00 ; set maximum instantaneous speed changes (mm/min) - default E120.00 ; M203 X12000.00 Y12000.00 Z2100.00 E12000.00 ; set maximum speeds (mm/min) ; M201 X1000.00 Y1000.00 Z100.00 E1000.00 ; set accelerations (mm/s^2) M906 X1200 Y1200 Z1000 E800 I30 ; set motor currents (mA) and motor idle factor in percent M84 S30 ; Set idle timeout ; Axis Limits M208 X5 Y0 Z0 S1 ; set axis minima M208 X305 Y305 Z284 S0 ; set axis maxima ; Endstops M574 X1 S3 ; configure sensorless endstop for low end on X M574 Y1 S3 ; configure sensorless endstop for low end on Y M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Filament Sensor M591 D0 P2 C"io8.out" S1 ; Filament Sensor an E0, Endstop IO8, Mode P1 Signal high wenn Filament da, S1: Pause on error ; Z leadscrew positions M671 X330:-35:150 Y115:115:370 S10 ; right, left, back - S Parameter for maximum Correction on G32 ; Z-Probe M558 P9 C"io7.in" F200 H5 R0.2 T9000 A1 B1 ; set Z probe type to bltouch and the dive height + speeds M950 S0 C"io7.out" ; create servo pin 0 for BLTouch G31 X-24.3 Y-34.1 Z1.3635 ; 63 set Z probe trigger value, offset and trigger height 1.67 M557 X15:270 Y5:270 S40 ; define mesh grid ; Heaters M308 S0 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp1 M950 H0 C"out1" T0 ; create bed heater output on out1 and map it to sensor 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M308 S1 P"temp2" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp2 M950 H1 C"out2" T1 ; create nozzle heater output on out2 and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"out8" Q10 ; create fan 1 on pin out8 and set its frequency M106 P0 C"Radial" S0 H-1 ; set fan 1 name and value. Thermostatic control is turned off M950 F1 C"out7" Q10 ; create fan 0 on pin out7 and set its frequency M106 P1 C"Hotend" S255 T45 H1 ; set fan 0 name and value. Thermostatic control is turned on (45°) ; Tools M563 P0 S"Mosquito" D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous ;M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss ; PID Tunings M307 H1 A555.0, C181.8, D6.3 S1 ; Hotend PID M307 H0 A378.1, C427.3, D3.9 S1 ; Bed PID