11:59:36 PMM122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet WiFi 1.02 or later Board ID: 08DJM-9178L-L4MSJ-6J1FG-3S46L-9S3AP Used output buffers: 3 of 24 (17 max) === RTOS === Static ram: 25712 Dynamic ram: 93212 of which 0 recycled Exception stack ram used: 464 Never used ram: 11684 Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,3728) IDLE(ready,160) Owned mutexes: === Platform === Last reset 03:40:36 ago, cause: software Last software reset at 2020-06-25 20:18, reason: User, spinning module GCodes, available RAM 11656 bytes (slot 1) Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d Error status: 0 Free file entries: 9 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest block write time: 43.3ms, max retries 0 MCU temperature: min 40.4, current 41.7, max 42.7 Supply voltage: min 23.8, current 24.2, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes Driver 0: standstill, SG min/max 0/530 Driver 1: ok, SG min/max not available Driver 2: standstill, SG min/max 0/541 Driver 3: ok, SG min/max 0/211 Driver 4: standstill, SG min/max not available Date/time: 2020-06-25 23:59:33 Cache data hit count 4294967295 Slowest loop: 149.69ms; fastest: 0.07ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Move === Hiccups: 0, FreeDm: 158, MinFreeDm: 116, MaxWait: 59162ms Bed compensation in use: mesh, comp offset 0.076 === DDARing === Scheduled moves: 44950, completed moves: 44943, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 === Heat === Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1 Heater 1 is on, I-accum = 0.6 === GCodes === Segments left: 1 Stack records: 2 allocated, 0 in use Movement lock held by null http is idle in state(s) 0 telnet is idle in state(s) 0 file is doing "G1 X354.502 Y426.463 E9.15458" in state(s) 0 serial is idle in state(s) 0 aux is idle in state(s) 0 daemon is idle in state(s) 0 queue is idle in state(s) 0 autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 111.92ms; fastest: 0.01ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0) HTTP sessions: 1 of 8 - WiFi - Network state is running WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.23 WiFi MAC address bc:dd:c2:31:9b:2b WiFi Vcc 3.40, reset reason Turned on by main processor WiFi flash size 4194304, free heap 25832 WiFi IP address 192.168.10.40 WiFi signal strength -52dBm, reconnections 0, sleep mode modem Socket states: 0 0 0 0 0 0 0 0 === Filament sensors === Extruder 0 sensor: ok