8:38:41 AMM122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05 running on Duet WiFi 1.02 or later
Board ID: 08DJM-9178L-L4MSJ-6J1FG-3S46L-9S3AP
Used output buffers: 3 of 24 (17 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93212 of which 0 recycled
Exception stack ram used: 480
Never used ram: 11668
Tasks: NETWORK(ready,628) HEAT(blocked,1232) MAIN(running,3728) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 12:19:41 ago, cause: software
Last software reset at 2020-06-25 20:18, reason: User, spinning module GCodes, available RAM 11656 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 41.5, current 43.2, max 44.8
Supply voltage: min 23.8, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/449
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max 0/554
Driver 3: ok, SG min/max 0/223
Driver 4: standstill, SG min/max not available
Date/time: 2020-06-26 08:38:37
Cache data hit count 4294967295
Slowest loop: 5.00ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 158, MinFreeDm: 121, MaxWait: 0ms
Bed compensation in use: mesh, comp offset 0.076
=== DDARing ===
Scheduled moves: 165510, completed moves: 165497, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = -1 -1 -1 -1, chamberHeaters = -1 -1
Heater 1 is on, I-accum = 0.6
=== GCodes ===
Segments left: 1
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X132.066 Y469.061 E90.15136" in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 202.20ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 1
WiFi firmware version 1.23
WiFi MAC address bc:dd:c2:31:9b:2b
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24248
WiFi IP address 192.168.10.40
WiFi signal strength -51dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0 sensor: ok