; Configuration file for Duet 3 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.3 on Fri Jul 03 2020 17:41:35 GMT-0400 (Eastern Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Duet3" ; set printer name M669 K1 ; select CoreXY mode ; Drives M569 P0.0 S1 ; physical drive 0.0 goes forwards M569 P0.1 S1 ; physical drive 0.1 goes forwards M569 P0.2 S1 ; physical drive 0.2 goes forwards M569 P0.3 S1 ; physical drive 0.3 goes forwards M569 P0.4 S1 ; physical drive 0.4 goes forwards M569 P0.5 S0 ; physical drive 0.5 goes forwards M584 X0.3 Y0.4 Z0.2:0.0:0.1 E0.5 ; set drive mapping Z-Motors: Right, Left, Rear M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X160.00 Y160.00 Z400.00 E412.40 ; set steps per mm M566 X600.00 Y600.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X10000.00 Y10000.00 Z1000.00 E1500.00 ; set maximum speeds (mm/min) M201 X3000.00 Y3000.00 Z20.00 E3000.00 ; set accelerations (mm/s^2) M906 X1200 Y1200 Z1000 E750 I50 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Z leadscrew positions M671 X330:-35:150 Y115:115:370 S10 ; right, left, back - S Parameter for maximum Correction on G32 ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X295 Y295 Z290 S0 ; set axis maxima ; Endstops M574 X1 S3 ; configure sensorless endstop for low end on X M574 Y1 S3 ; configure sensorless endstop for low end on Y M574 Z1 S2 ; configure Z-probe endstop for low end on Z M915 X Y S1 R0 ; Z-Probe M950 S0 C"io7.out" ; create servo pin 0 for BLTouch M558 P9 C"io7.in" F200 H5 R0.2 T9000 A1 B1 ; set Z probe type to bltouch and the dive height + speeds G31 P25 X30 Y33 Z3.4n ; set Z probe trigger value, offset and trigger height M557 X35:275 Y35:275 S60 ; define mesh grid ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp1 M950 H0 C"out0" T0 ; create bed heater output on out1 and map it to sensor 0 M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S145 ; set temperature limit for heater 0 to 145C M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp2 M950 H1 C"out1" T1 ; create nozzle heater output on out2 and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans ;M950 F0 C"out7" Q10 ; create fan 0 on pin out7 and set its frequency ;M106 P0 C"Hotend" S0 H1 T20 ; set fan 0 name and value. Thermostatic control is turned on M950 F1 C"out8" Q10 ; create fan 1 on pin out8 and set its frequency M106 P1 C"Radial" S0 H-1 ; set fan 1 name and value. Thermostatic control is turned off ; Tools M563 P0 S"e3d V6" D0 H1 F0:1 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; PID Tunings M307 H1 A555.0, C181.8, D6.3 S1 ; Hotend PID M307 H0 A378.1, C427.3, D3.9 S1 ; Bed PID