; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Wed May 22 2019 08:31:14 GMT+0200 (heure d’été d’Europe centrale) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M929 P"eventlog.txt" S1 ; Network M550 P"TOBECA_TM086" ; Set machine name M551 P"" ; Set password M552 P0.0.0.0 S1 ; Enable network and acquire dynamic address via DHCP M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S1 ; Enable Telnet ; Drives M569 P0 S0 M569 P1 S0 M569 P2 S0 M569 P3 S0 M569 P4 S1 M569 P5 S1 M569 P6 S1 M569 P7 S1 M569 P8 S1 M584 X0 Y1:2 Z5:6:7:8 E3:4 ; Apply custom drive mapping M350 X64 Y64 Z128 E16:16 I1 ; Configure microstepping with interpolation M92 X178.64 Y178.64 Z6400 E839.6:839.6 ; Set steps per mm M566 X200 Y200 Z12 E300.00:300.00 P1 ; Set maximum instantaneous speed changes (mm/min) M203 X30000.00 Y30000.00 Z150.00 E1500.00:1500.00 ; Set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E60.00:60.00 ; Set accelerations (mm/s^2) M906 X1700.00 Y2000.00 Z2400.00 E1200.00:1200.00 I30 ; Set motor currents (mA) and motor idle factor in per cent ; Axes supplémentaires pour mouvements indépendants des 4 vis Z ;M584 U5 V6 W7 A8 ; Apply custom drive mapping ;M350 U32 V32 W32 A32 ; Configure microstepping with interpolation ;M92 U1600 V1600 W1600 A1600 ; Set steps per mm ;M566 U24 V24 W24 A24 ; Set maximum instantaneous speed changes (mm/min) ;M203 U300 V300 W300 A300 ; Set maximum speeds (mm/min) ;M201 U20 V20 W20 Z20 ; Set accelerations (mm/s^2) ;M906 U2400 V2400 W2400 A2400 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; Set axis minima M208 X1550 Y1025 Z600 S0 ; Set axis maxima ; Endstops M574 X1 Y1 S1 ; Set active high endstops M574 Z1 ; Z-Probe M671 X-124.5:1670.5:-124.5:1670.5 Y54:54:1146.5:1146.5 S3 ; Définition des positions des vis Z pour auto-réglage des vis avec possibilité de mouvement de 3mm M558 P5 H12 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed G31 X-63 Y21 Z11.86 ; Heaters M305 P0 T100000 B3950 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H0 S150 ; Set temperature limit for heater 0 to 150C ; AVEC PT100 M305 P1 X200 M143 H1 S510 M305 P2 X201 M143 H2 S510 ; visu enceinte M305 P3 S"Enceinte" T100000 T100000 B4725 R4700 C7.06e-8 ; Set thermistor + ADC parameters for heater 0 M143 H3 S1 ; Fans M106 P0 S0 I0 F500 H-1 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off ;M106 P1 X50 ; Tools M563 P0 D0 H1 F0; define tool 0 M563 P1 D1 H2 F0; define tool 0 M563 P2 S"Enceinte" D0 H3 F0; pour visu temp enceinte G10 P0 S0 R0 X0 Y0 ; set tool 0 temperatures and offsets ; Sorties additionnelles (désactivation des heaters correspondants) M307 H6 A-1 C-1 D-1 ; Commande du variateur ventilateur M307 H4 A-1 C-1 D-1 ; Commande du régulateur de température M307 H5 A-1 C-1 D-1 ; Commande du mouvement du registre ; Automatic saving after power loss is not enabled ;M911 S22.0 R30.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Nozzle offsets G10 P0 X0 Y0 Z0 G10 P1 X49.9 Y1.9 Z0 ; Custom settings M501 ;T0