8/3/2020, 3:29:54 PM: M122  B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 408b
HEAT 1412 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2356
Last reset 01:01:27 ago, cause: power up
External motor driver(s)
Moves scheduled 11230, completed 11230, in progress 0, hiccups 0
No step interrupt scheduled
VIN: 24.2V
MCU temperature: min 22.8C, current 26.3C, max 26.4C
Ticks since heat task active 27, ADC conversions started 1843760, completed 1843760, timed out 0
Last sensors broadcast 00000000 found 0 30 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000a4e GAIN 01493e OFFS 002874 CAL 1f28
8/3/2020, 3:29:58 PM: M122  B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 368b
HEAT 1404 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2356
Last reset 01:01:31 ago, cause: power up
External motor driver(s)
Moves scheduled 11319, completed 11318, in progress 1, hiccups 0
Next step interrupt due in 143 ticks, enabled
VIN: 24.6V
MCU temperature: min 24.3C, current 27.6C, max 27.7C
Ticks since heat task active 94, ADC conversions started 1845669, completed 18456Last sensors broadcast 00000000 found 0 97 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000aca GAIN 0155f1 OFFS 00280f CAL 1f2c
8/3/2020, 3:30:02 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (25 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 162916 of which 60 recycled
Exception stack ram used: 504
Never used ram: 75132
Tasks: NETWORK(ready,1972) HEAT(blocked,1188) CanReceiv(suspended,3820) CanSender(suspended,1428) CanClock(blocked,1436) TMC(blocked,68) MAIN(running,4512) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:13:50 ago, cause: software
Last software reset at 2020-08-03 20:16, reason: User, spinning module LinuxInterface, available RAM 75432 bytes (slot 3)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 45.2, current 45.3, max 45.5
Supply voltage: min 23.7, current 23.9, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: standstill, reads 62557, writes 0 timeouts 0, SG min/max not available
Driver 1: ok, reads 62557, writes 0 timeouts 0, SG min/max 0/154
Driver 2: ok, reads 62556, writes 0 timeouts 0, SG min/max 0/179
Driver 3: standstill, reads 62557, writes 0 timeouts 0, SG min/max not available
Driver 4: ok, reads 62556, writes 0 timeouts 0, SG min/max 0/160
Driver 5: ok, reads 62557, writes 0 timeouts 0, SG min/max 0/154
Date/time: 2020-08-03 20:30:02
Slowest loop: 14.81ms; fastest: 0.21ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 364, MinFreeDm: 356, MaxWait: 0ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 12375, completed moves: 12315, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0.1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is doing "G1 X85.000999 Y21.566000 E0.504000" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.50ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 2836, longest wait 6ms for type 6024
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 17ms ago
RX/TX seq numbers: 26493/26495
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 1296/2184-0
=== Duet Control Server ===
Duet Control Server v3.1.1
File:
Buffered code: G1 X87.640 Y22.631 E0.5453
Buffered code: G1 X88.159 Y22.891 E0.5537
Buffered code: G1 X88.827 Y23.254 E0.5648
Buffered code: G1 X89.318 Y23.540 E0.5730
Buffered code: G1 X89.953 Y23.939 E0.5839
Buffered code: G1 X90.425 Y24.255 E0.5921
Buffered code: G1 X91.043 Y24.699 E0.6031
Buffered code: G1 X91.503 Y25.053 E0.6116
Buffered code: G1 X92.083 Y25.527 E0.6224
Buffered code: G1 X92.521 Y25.909 E0.6308
Buffered code: G1 X93.069 Y26.419 E0.6417
Buffered code: G1 X93.481 Y26.828 E0.6501
Buffered code: G1 X93.995 Y27.372 E0.6610
Buffered code: G1 X94.498 Y27.943 E0.6720
Buffered code: G1 X94.860 Y28.382 E0.6803
Buffered code: G1 X95.326 Y28.984 E0.6913
Buffered code: G1 X95.768 Y29.600 E0.7023
Buffered code: G1 X96.290 Y30.396 E0.7161
Buffered code: G1 X96.658 Y31.006 E0.7264
Buffered code: G1 X96.750 Y31.197 E0.7295
Buffered code: G1 X96.805 Y31.384 E0.7323
Buffered code: G1 X96.826 Y31.572 E0.7351
Buffered code: G1 X96.816 Y31.761 E0.7378
Buffered code: G1 X96.771 Y31.948 E0.7406
Buffered code: G1 X96.694 Y32.136 E0.7435
==> 1196 bytes
Pending code: G1 X96.405 Y32.626 E0.7518
Pending code: G1 X95.997 Y33.267 E0.7628
Pending code: G1 X95.334 Y34.212 E0.7795
Pending code: G1 X94.878 Y34.804 E0.7904
Code buffer space: 1432
Configured SPI speed: 8000000 Hz
Full transfers per second: 31.40
File /opt/dsf/sd/gcodes/3DBenchy (1).gcode is selected, processing
8/3/2020, 3:30:16 PM: M122 B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 408b
HEAT 1412 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2332
Last reset 01:01:49 ago, cause: power up
External motor driver(s)
Moves scheduled 11738, completed 11737, in progress 1, hiccups 0
Next step interrupt due in 19 ticks, enabled
VIN: 24.2V
MCU temperature: min 22.8C, current 26.3C, max 26.4C
Ticks since heat task active 224, ADC conversions started 1854984, completed 18549Last sensors broadcast 00000000 found 0 228 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000a4e GAIN 01493e OFFS 002874 CAL 1f28
8/3/2020, 3:30:20 PM: M122 B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 368b
HEAT 1404 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2356
Last reset 01:01:53 ago, cause: power up
External motor driver(s)
Moves scheduled 11892, completed 11885, in progress 1, hiccups 0
Next step interrupt due in 14 ticks, enabled
VIN: 24.6V
MCU temperature: min 24.3C, current 27.6C, max 27.7C
Ticks since heat task active 184, ADC conversions started 1856839, completed 18568Last sensors broadcast 00000000 found 0 187 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000aca GAIN 0155f1 OFFS 00280f CAL 1f2c
8/3/2020, 3:30:24 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (25 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 162916 of which 60 recycled
Exception stack ram used: 504
Never used ram: 75132
Tasks: NETWORK(ready,1972) HEAT(blocked,1188) CanReceiv(suspended,3820) CanSender(suspended,1428) CanClock(blocked,1436) TMC(blocked,68) MAIN(running,4512) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:14:12 ago, cause: software
Last software reset at 2020-08-03 20:16, reason: User, spinning module LinuxInterface, available RAM 75432 bytes (slot 3)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 45.2, current 45.3, max 45.5
Supply voltage: min 23.7, current 23.9, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: standstill, reads 40597, writes 0 timeouts 0, SG min/max not available
Driver 1: ok, reads 40597, writes 0 timeouts 0, SG min/max 0/256
Driver 2: standstill, reads 40597, writes 0 timeouts 0, SG min/max 0/1023
Driver 3: standstill, reads 40597, writes 0 timeouts 0, SG min/max not available
Driver 4: standstill, reads 40597, writes 0 timeouts 0, SG min/max 0/1023
Driver 5: standstill, reads 40597, writes 0 timeouts 0, SG min/max 0/1023
Date/time: 2020-08-03 20:30:24
Slowest loop: 15.79ms; fastest: 0.21ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 374, MinFreeDm: 357, MaxWait: 0ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 13006, completed moves: 12946, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0.1
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is doing "G1 X53.342999 Y30.542999" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.48ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 1330, longest wait 6ms for type 6024
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 23ms ago
RX/TX seq numbers: 27178/27180
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 1040/2200-0
=== Duet Control Server ===
Duet Control Server v3.1.1
File:
Buffered code: G1 X53.343 Y30.543
Buffered code: G1 X53.343 Y31.350
Buffered code: G1 X54.677 Y31.653
Buffered code: G92 E0.0000
Buffered code: G1 X54.709 Y31.685 E0.0006 F4363
Buffered code: G92 E0.0000
Buffered code: G1 E-0.4000 F2400
Buffered code: G1 X90.790 Y37.218 F12000
Buffered code: G1 E0.0000 F2400
Buffered code: G92 E0.0000
Buffered code: G1 X91.093 Y36.966 E0.0058 F4363
Buffered code: G1 X91.159 Y36.908 E0.0071
Buffered code: G1 X91.167 Y36.917 E0.0072
Buffered code: G1 X91.534 Y36.605 E0.0142
Buffered code: G1 X91.519 Y36.589 E0.0145
Buffered code: G1 X91.878 Y36.270 E0.0215
Buffered code: G1 X91.894 Y36.286 E0.0218
Buffered code: G1 X92.202 Y36.004 E0.0279
Buffered code: G1 X92.247 Y35.960 E0.0288
Buffered code: G1 X92.221 Y35.934 E0.0293
Buffered code: G1 X92.562 Y35.597 E0.0363
Buffered code: G1 X92.589 Y35.623 E0.0368
Buffered code: G1 X92.713 Y35.500 E0.0394
Buffered code: G1 X92.922 Y35.278 E0.0438
Buffered code: G1 X92.890 Y35.245 E0.0445
Buffered code: G1 X93.213 Y34.889 E0.0514
Buffered code: G1 X93.251 Y34.927 E0.0522
Buffered code: G1 X93.336 Y34.836 E0.0540
Buffered code: G1 X93.568 Y34.566 E0.0592
Buffered code: G1 X93.525 Y34.523 E0.0601
Buffered code: G1 X93.830 Y34.149 E0.0671
Buffered code: G1 X93.880 Y34.199 E0.0681
==> 1448 bytes
Code buffer space: 1612
Configured SPI speed: 8000000 Hz
Full transfers per second: 31.34
File /opt/dsf/sd/gcodes/3DBenchy (1).gcode is selected, processing
8/3/2020, 3:30:34 PM: M122 B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 408b
HEAT 1412 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2332
Last reset 01:02:07 ago, cause: power up
External motor driver(s)
Moves scheduled 12169, completed 12168, in progress 1, hiccups 0
Next step interrupt due in 34888 ticks, enabled
VIN: 24.2V
MCU temperature: min 22.8C, current 26.3C, max 26.4C
Ticks since heat task active 226, ADC conversions started 1863860, completed 18Last sensors broadcast 00000000 found 0 229 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000a4e GAIN 01493e OFFS 002874 CAL 1f28
8/3/2020, 3:30:37 PM: M122 B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 368b
HEAT 1404 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2356
Last reset 01:02:10 ago, cause: power up
External motor driver(s)
Moves scheduled 12333, completed 12326, in progress 1, hiccups 0
Next step interrupt due in 129 ticks, enabled
VIN: 24.6V
MCU temperature: min 24.3C, current 27.6C, max 27.7C
Ticks since heat task active 118, ADC conversions started 1865431, completed 1865Last sensors broadcast 00000000 found 0 121 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000aca GAIN 0155f1 OFFS 00280f CAL 1f2c
8/3/2020, 3:31:02 PM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.1.1 running on Duet 3 MB6HC v1.01 or later (SBC mode)
Board ID: 08DJM-956L2-G43S8-6J9DG-3S46Q-KV2GD
Used output buffers: 1 of 40 (25 max)
=== RTOS ===
Static ram: 154604
Dynamic ram: 162916 of which 60 recycled
Exception stack ram used: 504
Never used ram: 75132
Tasks: NETWORK(ready,1972) HEAT(blocked,1188) CanReceiv(suspended,3820) CanSender(suspended,1428) CanClock(blocked,1436) TMC(blocked,68) MAIN(running,4512) IDLE(ready,76)
Owned mutexes:
=== Platform ===
Last reset 00:14:50 ago, cause: software
Last software reset at 2020-08-03 20:16, reason: User, spinning module LinuxInterface, available RAM 75432 bytes (slot 3)
Software reset code 0x0010 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0444a000 BFAR 0x00000000 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 45.3, current 45.4, max 45.6
Supply voltage: min 23.7, current 23.7, max 23.9, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Driver 0: standstill, reads 55266, writes 0 timeouts 0, SG min/max not available
Driver 1: ok, reads 55266, writes 0 timeouts 0, SG min/max 0/153
Driver 2: ok, reads 55266, writes 0 timeouts 0, SG min/max 0/180
Driver 3: standstill, reads 55266, writes 0 timeouts 0, SG min/max not available
Driver 4: ok, reads 55266, writes 0 timeouts 0, SG min/max 0/172
Driver 5: ok, reads 55266, writes 0 timeouts 0, SG min/max 0/149
Date/time: 2020-08-03 20:31:02
Slowest loop: 15.07ms; fastest: 0.21ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 371, MinFreeDm: 356, MaxWait: 0ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 14184, completed moves: 14160, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0.1
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP* is ready with "M122" in state(s) 0
Telnet is idle in state(s) 0
File* is doing "G1 X88.005997 Y39.365002 E2.860200" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue* is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon* is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.67ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 0 of 8
- Ethernet -
State: disabled
Error counts: 0 0 0 0 0
Socket states: 0 0 0 0 0 0 0 0
=== CAN ===
Messages sent 2547, longest wait 6ms for type 6024
=== Linux interface ===
State: 0, failed transfers: 0
Last transfer: 19ms ago
RX/TX seq numbers: 28379/28381
SPI underruns 0, overruns 0
Number of disconnects: 0
Buffer RX/TX: 2652/72-4092
=== Duet Control Server ===
Duet Control Server v3.1.1
File:
Buffered code: G1 X88.006 Y39.365 E2.8602
Buffered code: G1 X87.682 Y39.539 E2.8658
Buffered code: G1 X86.757 Y39.974 E2.8812
Buffered code: G1 X69.053 Y22.270 E3.2587
Buffered code: G1 X67.356 Y22.431 E3.2844
Buffered code: G1 X85.429 Y40.504 E3.6698
Buffered code: G1 X84.593 Y40.792 E3.6832
Buffered code: G1 X84.022 Y40.954 E3.6921
Buffered code: G1 X65.659 Y22.592 E4.0837
Buffered code: G1 X63.963 Y22.753 E4.1094
Buffered code: G1 X82.531 Y41.321 E4.5054
Buffered code: G1 X82.439 Y41.342 E4.5068
Buffered code: G1 X81.717 Y41.473 E4.5179
Buffered code: G1 X81.173 Y41.553 E4.5262
Buffered code: G1 X80.934 Y41.582 E4.5298
Buffered code: G1 X62.266 Y22.914 E4.9279
Buffered code: G1 X60.569 Y23.075 E4.9536
Buffered code: G1 X79.216 Y41.722 E5.3513
Buffered code: G1 X79.156 Y41.725 E5.3522
Buffered code: G1 X78.612 Y41.738 E5.3604
Buffered code: G1 X77.876 Y41.732 E5.3715
Buffered code: G1 X77.345 Y41.709 E5.3795
Buffered code: G1 X58.872 Y23.235 E5.7734
Buffered code: G1 X57.175 Y23.396 E5.7991
Buffered code: G1 X75.314 Y41.535 E6.1860
Buffered code: G1 X73.258 Y41.337 E6.2171
Buffered code: G1 X55.478 Y23.557 E6.5963
Buffered code: G1 X53.781 Y23.718 E6.6220
Buffered code: G1 X71.202 Y41.139 E6.9935
Buffered code: G1 X69.146 Y40.941 E7.0246
Buffered code: G1 X52.084 Y23.879 E7.3885
Buffered code: G1 X51.995 Y23.887 E7.3898
==> 1504 bytes
Code buffer space: 2580
Configured SPI speed: 8000000 Hz
Full transfers per second: 31.24
File /opt/dsf/sd/gcodes/3DBenchy (1).gcode is selected, processing
8/3/2020, 3:31:10 PM: M122 B40: Diagnostics for board 40:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 408b
HEAT 1412 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2332
Last reset 01:02:43 ago, cause: power up
External motor driver(s)
Moves scheduled 13193, completed 13191, in progress 1, hiccups 0
Next step interrupt due in 7350 ticks, enabled
VIN: 24.3V
MCU temperature: min 22.8C, current 26.3C, max 26.4C
Ticks since heat task active 160, ADC conversions started 1881702, completed 188Last sensors broadcast 00000000 found 0 163 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000a4e GAIN 01493e OFFS 002874 CAL 1f28
8/3/2020, 3:31:14 PM: M122 B41: Diagnostics for board 41:
Board EXP1XD firmware 3.1.0+ (2020-07-01b3)
Never used RAM 11.1Kb, max stack 368b
HEAT 1404 CanAsync 1448 CanRecv 1436 AIN 608 MAIN 2356
Last reset 01:02:47 ago, cause: power up
External motor driver(s)
Moves scheduled 13367, completed 13362, in progress 1, hiccups 0
Next step interrupt due in 257 ticks, enabled
VIN: 24.6V
MCU temperature: min 24.3C, current 27.6C, max 27.7C
Ticks since heat task active 92, ADC conversions started 1883543, completed 18835Last sensors broadcast 00000000 found 0 95 ticks ago
Free CAN buffers: 36
NVM user row b1d088a9 fffff8bb a 0
TSENS 000aca GAIN 0155f1 OFFS 00280f CAL 1f2c