; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Mon Jul 20 2020 11:09:25 GMT-0500 (Central Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Dozer" ; set printer name M555 P2 ; Set firmware compatibility to look like Marlin M669 K1 ; select CoreXY mode ; Network M551 P"DozerEntry" ; set password M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes backwards M569 P1 S0 ; physical drive 1 goes backwards M569 P2 S0 ; physical drive 2 goes backwards M569 P3 S0 ; physical drive 3 goes backwards M584 X0 Y1 Z2 E3 ; set drive mapping M350 E8 I0 ; test seperate extruder settings M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation M92 X200.00 Y200.00 Z1600.00 E413.00 ; set steps per mm M566 X480.00 Y480.00 Z120.00 E600.00 ; set maximum instantaneous speed changes (mm/min) M203 X15000.00 Y15000.00 Z750.00 E4800.00 ; set maximum speeds (mm/min) M201 X1250.00 Y1250.00 Z400.00 E5000.00 ; set accelerations (mm/s^2) M906 X1250 Y1250 Z1000 E1000 I25 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-84 Y-85 Z0 S1 ; set axis minima M208 X91 Y90 Z220 S0 ; set axis maxima ; Endstops M574 X1 S3 ; configure sensorless endstop for low end on X M574 Y2 S3 ; configure sensorless endstop for high end on Y M574 Z1 S2 ; configure Z-probe endstop for low end on Z ; Z-Probe M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch M558 P9 C"^zprobe.in" H5 F250 T6000 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X-12.5 Y27.5 Z1.94 ; set Z probe trigger value, offset and trigger height M557 X-52.5:52.5 Y-52.5:52.5 P2:2 ; define mesh grid M671 X-80.0:80.0:-80.0 Y-50.0:0.0:50.0 ; define bed adjustement points ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 A517.0 C609.6 D2.3 S1.00 V24.4 B0 ; set PID values for bed heater M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 A554.7 C248.3 D5.4 S1.00 V24.3 B0 ; set PID values for hotend ; MCU Temp Sense M308 S3 Y"mcu-temp" A"MCU" ; configure sensor 3 as thermistor for mcu temp ; Fans M950 F0 C"fan0" Q100 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q100 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"fan2" Q100 ; create fan 2 on pin fan2 and set its frequency M106 P2 S1 H0:1:3 T45 ; set fan 2 value. Thermostatic control is turned on ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined