8/23/2020, 11:11:11 AM: Connected to 192.168.1.150
8/23/2020, 11:16:36 AM: Upload of config.g successful after 0s
8/23/2020, 11:16:48 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:16:49 AM: Connection established
8/23/2020, 11:19:03 AM: Upload of config.g successful after 0s
8/23/2020, 11:19:14 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:19:29 AM: Connection established
8/23/2020, 11:23:51 AM: Upload of config.g successful after 0s
8/23/2020, 11:24:03 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:24:09 AM: Connection established
8/23/2020, 11:24:25 AM: M120
G91
G1 X0.1 F6000
G90
M121: Error: G0/G1: insufficient axes homed
8/23/2020, 11:26:02 AM: Upload of config.g successful after 0s
8/23/2020, 11:26:13 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:26:28 AM: Connection established
8/23/2020, 11:26:33 AM: M120
G91
G1 X0.1 F6000
G90
M121: Error: G0/G1: insufficient axes homed
8/23/2020, 11:26:54 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:29:01 AM: Connection established
8/23/2020, 11:31:15 AM: M98 P"0:/macros/04-Test_motors": Error: in file macro line 8 column 30: M906: array too long, max length = 1
Error: in file macro line 12 column 22: M350: array too long, max length = 1
Error: in file macro line 13 column 21: M92: array too long, max length = 1
Error: in file macro line 14 column 30: M906: array too long, max length = 1
Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
8/23/2020, 11:31:23 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:31:32 AM: Connection established
8/23/2020, 11:34:14 AM: Upload of config.g successful after 0s
8/23/2020, 11:34:27 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:34:42 AM: Connection established
8/23/2020, 11:35:22 AM: M98 P"0:/macros/04-Test_motors": Error: in file macro line 8 column 30: M906: array too long, max length = 1
Error: in file macro line 12 column 22: M350: array too long, max length = 1
Error: in file macro line 13 column 21: M92: array too long, max length = 1
Error: in file macro line 14 column 30: M906: array too long, max length = 1
Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
8/23/2020, 11:35:24 AM: : Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
8/23/2020, 11:35:33 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:35:48 AM: Connection established
8/23/2020, 11:36:40 AM: M122: === Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 08DLM-996RU-N85S4-7JTD8-3S46M-9VBBP
Used output buffers: 3 of 24 (11 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 92936 of which 60 recycled
Exception stack ram used: 264
Never used ram: 9832
Tasks: NETWORK(ready,384) HEAT(blocked,1304) MAIN(running,1824) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:01:02 ago, cause: power up
Last software reset at 2020-08-23 11:34, reason: User, spinning module GCodes, available RAM 9832 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 18.6, current 21.5, max 21.9
Supply voltage: min 24.1, current 24.3, max 24.5, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2020-08-23 11:36:36
Cache data hit count 101062551
Slowest loop: 4.82ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.75ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address ec:fa:bc:5b:47:ab
WiFi Vcc 3.43, reset reason Unknown
WiFi flash size 4194304, free heap 23408
WiFi IP address 192.168.1.150
WiFi signal strength -55dBm, reconnections 0, sleep mode modem
Socket states: 4 0 0 0 0 0 0 0
8/23/2020, 11:37:47 AM: Connection interrupted, attempting to reconnect...: HTTP request timed out
8/23/2020, 11:43:27 AM: Connection established
8/23/2020, 11:45:10 AM: Download of config.g successful after 0s
8/23/2020, 11:45:19 AM: Download of config.g successful after 0s
8/23/2020, 11:51:20 AM: M120
G91
G1 Y-50 F6000
G90
M121: Error: G0/G1: insufficient axes homed