; RRF3 Config ; Network M550 P"Voron V2.049" ; Set machine name M552 S1 ; Enable network M586 P0 S1 ; Enable HTTP (for DWC) M586 P1 S1 T0 ; Enable FTP (for remote backups) M586 P2 S1 T0 ; Disable Telnet ; General Settings M111 S0 ; Debugging Off G21 ; Millimeter Units G90 ; Absolute Tool Cords M83 ; Relative Extruder M575 P1 S1 B57600 ; Enable PanelDue M667 S1 ; CoreXY type M669 K1 ; CoreXY type ; Drive Mechanics ; --- map --- ; _______ ; | 6 | 7 | ; | ----- | ; | 5 | 8 | ; ------- ; front ; ; LEFT______Right ; | B:0 | A:1 | ; ----------------- M569 P0 S1 ; A (X) M569 P1 S1 ; B (Y) M569 P3 S1 ; Extruder (E0) M569 P5 S1 ; Z1 (E2) M569 P6 S0 ; Z2 (E3) M569 P7 S1 ; Z3 (E4) M569 P8 S0 ; Z4 (E5) M584 X0 Y1 Z5:6:7:8 E3 ; Bind Motors M350 X16 Y16 Z16 E16:16 I1 ; Use 1/16 microstepping with interpolation M92 X160 Y160 Z800 ; Set XYZ steps per mm (0.9deg motors) M92 E415:415 ; Set Extruder steps per mm (After Burner) ;M350 Z16 I0 ; Disable Z interpolation M906 X1200 Y1200 Z1200 E600 ; Motor Currents M84 S3600 ; Motor Idle timeout (1 Hr) M906 I50 ; Motor Idle current percentage M574 X2 S1 P"!^duex.e3stop" ; X active high endstop switch M574 Y2 S1 P"!^duex.e2stop" ; Y active high endstop switch M574 Z0 C"nil" ; Free up Z endstop M913 X100 Y100 ; restore motor current percentage to 100% M203 X18000 Y18000 E9000 ; maximum speed (mm/min) M201 X2000 Y2000 E4500 ; maximum acceleration (mm/sec^2) M566 X3000 Y3000 E8000 ; instantaneous speed change (mm/min) M913 Z100 ; restore motor current percentage to 100% M203 Z3000 ; maximum speed (mm/min) M201 Z250 ; maximum acceleration (mm/min/s) M566 Z60 ; instantaneous speed change (mm/min) M400 ; Clear the move buffer M558 P8 C"^zprobe.in" A5 H5 R0.2 S0.01 F1200 T18000 A1 B0 ; Activate Z Probe G31 P500 X0 Y25 Z1.7 ; Set Probe offsets G4 P200 ; Dwell for 200ms ; Printer Geometry M671 X-60:-60:410:410 Y-10:420:420:-10 S20 ; Define Z belts locations (Front_Left, Back_Left, Back_Right, Front_Right) M208 X0 Y0 Z-3 S1 ; Minimal Axes M208 X350 Y350 Z350 S0 ; Maximum Axes M557 X25:325 Y25:295 S25 ; Define bed mesh grid (inductive probe, positions include the Z offset!) ; Pressure advance M572 D0 S0.025 ; DAA M593 F39.3 ; Thermal Settings ;; Bed M308 S0 P"bedtemp" Y"thermistor" R4700 T100000 B3950 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"bedheat" T0 ; create bed heater output on out0 and map it to sensor 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 S0.85 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; Declare H0 as bed heater ;; Hotend M308 S1 P"spi.cs1" Y"rtdmax31865" ; configure sensor 1 as thermocouple via CS pin spi.cs1 M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 275C M307 H1 B0 S1.00 ; disable bang-bang mode for the nozzle heater and set PWM limit ;; Chamber M308 S3 P"duex.cs6" Y"dht22" A"Chamber Temp" ; Temperature M308 S4 P"S3.1" Y"dhthumidity" A"Chamber Hum[%]" ; Humidity ;; Boards M308 S5 Y"drivers" A"Drivers-Duet" M308 S6 Y"drivers-duex" A"Drivers-Duex" M308 S7 Y"mcu-temp" A"MCU" ;; PID Settings M307 H2 B1 S0.01 V23.7 ;PID for chamber set to reduce chance of faults with no heater M307 H0 A301.0 C845.3 D1.4 S1.00 V23.6 B0 M307 H1 A497.2 C209.9 D3.3 S1.00 V23.6 B0 ; Dragon Non-HF W/ Sock ;; MCU Temp Calibration M912 P0 S-13 ; Fans M106 P1 H-1 ; Disable auto thermal mode on Fan1 ;; Part Cooling M950 F0 C"duex.fan4" Q500 M106 P0 S0 C"Part Fan" ;; Hotend Fan M950 F1 C"duex.fan3" Q500 M106 P1 T45 H1 C"Hotend Fan" ;; Basement Cooling M950 F2 C"fan1" Q500 M106 P2 T45 H1 C"Basement Fan" ;; Exhaust Fan M950 F3 C"fan0" Q500 M106 P3 T45 H1 C"Exhaust Fan" ; Tools M563 P0 D0 H1 ; bind tool 0 to drive and heater G10 P0 X0 Y0 Z0 ; tool offset G10 P0 S0 R0 ; tool active and standby temp T0 ; activate tool 0 ; Case Lighting M950 P6 C"duex.e2heat" Q500 ; Green LED M950 P7 C"duex.e3heat" Q500 ; Red LED M950 P8 C"duex.e4heat" Q500 ; Blue LED M950 P9 C"duex.e5heat" Q500 ; White LED M42 P6 S0 M42 P7 S0 M42 P8 S0 M42 P9 S1 ; Enable Logging ;M929 P"eventlog.txt" S1