M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-956GU-DJMSN-6J1F0-3S46M-KVQ7H
Used output buffers: 3 of 24 (18 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 94352 of which 44 recycled
Exception stack ram used: 552
Never used ram: 8144
Tasks: NETWORK(ready,668) HEAT(blocked,1168) DUEX(suspended,160) MAIN(running,1640) IDLE(ready,80)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 04:33:43 ago, cause: software
Last software reset at 2020-10-02 16:48, reason: User, spinning module GCodes, available RAM 8168 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
Error status: 0
MCU temperature: min 31.5, current 34.8, max 35.4
Supply voltage: min 24.3, current 24.5, max 24.8, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max 0/780
Driver 1: ok, SG min/max 0/1023
Driver 2: standstill, SG min/max not available
Driver 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Driver 5: ok, SG min/max 0/1023
Driver 6: ok, SG min/max 0/1023
Driver 7: ok, SG min/max 0/1023
Driver 8: ok, SG min/max 0/1023
Driver 9: standstill, SG min/max not available
Date/time: 2020-10-02 21:21:48
Cache data hit count 4294967295
Slowest loop: 123.83ms; fastest: 0.12ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 2.0ms, write time 26.3ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 165, MinFreeDm: 145, MaxWait: 3378916ms
Bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 1901, completed moves: 1893, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: 3
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0  CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.1
Heater 1 is on, I-accum = 0.8
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X135.685 Y174.768 E0.96834" in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 38.21ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 2 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 5c:cf:7f:76:6e:c1
WiFi Vcc 3.32, reset reason Unknown
WiFi flash size 4194304, free heap 24192
WiFi IP address 192.168.1.192
WiFi signal strength -51dBm, reconnections 0, sleep mode modem
Socket states: 4 0 0 0 0 0 0 0
=== DueX ===
Read count 1, 0.00 reads/min