; Configuration file for Duet 3 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Thu May 14 2020 14:51:44 GMT+0100 (British Summer Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Duet3" ; set printer name M552 S1 M575 P1 B57600 S1 ; Drives M569 P0.0 S0 ; physical drive 0.0 goes backwards M569 P0.1 S1 ; physical drive 0.1 goes forwards M569 P0.2 S1 ; physical drive 0.2 goes forwards M569 P0.4 S1 ; physical drive 0.4 goes forwards M584 X0.0 Y0.1 Z0.2:0.3 E0.4 ; set drive mapping M671 X-65:345 Y-110:-110 S2 ; lead screw positioning for true bed leveling M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation ; Titan - 1.8 = E437 ; BMG - 0.9 = E808 M92 X160.00 Y80.00 Z400.00 E808 ; set steps per mm M566 X900.00 Y900.00 Z80.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X15000.00 Y15000.00 Z3750.00 E2500.00 ; set maximum speeds (mm/min) M201 X2000.00 Y2000.00 Z2000.00 E250.00 ; set accelerations (mm/s^2) M906 X1344 Y1600 Z1344 E800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X-25 Y-10 Z0 S1 ; set axis minima M208 X325 Y238 Z300 S0 ; set axis maxima ; Endstops M574 X2 S1 P"io3.in" ; configure active-high endstop for high end on X via pin io0.in M574 Y2 S1 P"!io1.in" ; configure active-high endstop for high end on Y via pin io1.in ; Z-Probe ;M950 S0 C"io7.out" ; create servo pin 0 for BLTouch ;M558 P9 C"^io7.in" H10 F600 T9000 ; set Z probe type to bltouch and the dive height + speeds ;G31 P500 X27 Y0 Z0.31 ; set Z probe trigger value, offset and trigger height ;M557 X15:265 Y20:220 S40 ; define mesh grid ; DC42 M558 P8 C"io2.in" H10 F600 T9000 G31 P500 X0 Y-16 Z2.6 M557 X15:265 Y20:220 S40 ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency M106 P0 S1 H1 T45 ; set fan 0 value. Thermostatic control is turned on M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off M308 S2 Y"drivers" A"DRIVERS" M308 S3 Y"mcu-temp" A"MCU" M950 F2 C"out9" Q500 M106 P2 T45:65 H2:3 ; Tools M563 P0 S"Bowden Extruder" D0 H1 F0:1 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Heater model parameters ; M307 H0 A116.0 C575.4 D2.5 V11.2 B0 ; M307 H1 A513.4 C169.9 D4.4 V23.9 B0 ; Miscellaneous M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss M564 H0 M501 ; M572 D0 S0.4 ; Pressure Advance ; M929 P"eventlog.txt" S1