; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool on Sat Oct 13 2018 22:05:59 GMT-0600 (Mountain Daylight Time) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 PMy printer ; Set machine name M552 S1 ; Enable network ;*** Access point is configured manually via M587 M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S0 ; Drive 0 goes backwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S1 ; Drive 3 goes forwards M569 P5 S1 M569 P6 S1 M569 P7 S0 M569 P8 S0 M569 P5 T3 M569 P6 T3 M569 P7 T5 M569 P8 T5 M584 X6 Y5 Z7:8 E3 ; Apply custom drive mapping M350 X256 Y256 Z128 I0 ; Configure microstepping without interpolation M350 E16 I1 ; Configure microstepping with interpolation M92 X637.5 Y3977 Z1295 E418 ; Set steps per mm M566 X60 Y60 Z12 E120 ; Set maximum instantaneous speed changes (mm/min) M203 X3000 Y3000 Z600 E1200 ; Set maximum speeds (mm/min) M201 X80 Y80 Z70 E250 ; Set accelerations (mm/s^2) M906 X800 Y800 Z800 E1700 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; Set axis minima M208 X940 Y790 Z695 S0 ; Set axis maxima ; Endstops M574 X1 Y1 S0 ; Set active low endstops ; Z-Probe M574 Z10 S2 ; Set endstops controlled by probe M307 H3 A-1 C-1 D-1 ; Disable heater on PWM channel for BLTouch M558 P5 X0 Y0 Z1 H10 F200 T5000 ; Set Z probe type to bltouch and the dive height + speeds G31 P25 X47 Y5 Z1.15 ; Set Z probe trigger value, offset and trigger height ; Heaters M305 P0 T100000 B3950 ; set bed thermistor parameters M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 R4700 B4725 C7.060000e-8 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P2 S1 I0 F500 H T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X-40 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured