; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.0 on Wed Dec 30 2020 15:03:09 GMT+1030 (Australian Central Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"DuetBeastV1" ; set printer name ; Network M551 P"Satelite~3" ; set password M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S1 ; physical drive 1 goes forwards M569 P2 S1 ; physical drive 2 goes forwards ;M569 P3 S1 ; physical drive 3 goes forwards M569 P5 S1 ; physical drive 5 goes forwards (Added 20201230c) M569 P6 S1 ; physical drive 6 goes forwards (Added 20201230c) M569 P7 S1 ; physical drive 7 goes forwards (Added 20201230c) ;M584 X0 Y1 Z2 E3 ; set drive mapping (default commented out 20201230c) M584 X0 Y1 Z5:6:7 E3 ; three Z motors connected to driver outputs 5, 6 and 7 (front left, middle rear, front right) M671 X-105:180:450 Y-75:480:-75 S10 ; leadscrews at front left, middle rear, front right, max correction of 10 mm M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z400.00 E420.00 ; set steps per mm M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X400 Y380 Z600 S0 ; set axis maxima ; Endstops ;M574 X1 Y1 S0 P"xstop" ; FAILED, S0 is deprecated; configure active-low endstop for low end on X via pin xstop and Y via pin ystop M574 X1 S1 P"!xstop" ; configure active-low endstop for low end on X via pin xstop M574 Y1 S1 P"!ystop" ; configure active-low endstop for low end on Y via pin ystop M574 Z1 S2 ; Define Z to use Probe. Home to Min ; Z-Probe M950 S0 C"duex.pwm5" ; create servo pin 0 for BLTouch ;M558 P5 H5 F500 T4000 X0 Y0 Z1 ; Set Z probe type/mode 5. H=Dive Height. F=Speed the bed moves (From Example) ;M558 P9 C"^zprobe.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds (Default from config gen tool) M558 P9 H5 F500 T4000 X0 Y0 Z1 ; Set Z probe type/mode 9. H=Dive Height. F=Speed the bed moves (My Hacked version) M558 H30 ;*** Remove this line after delta calibration has been done and new delta parameters have been saved ; Z-Prob Offsets G31 P500 X-38.0 Y-1.2 Z0.0 ; set Z probe trigger value, offset and trigger height ; Mesh Grid M557 X15:380 Y15:380 S100 ; define mesh grid ; Heaters M140 H-1 ; disable heated bed (overrides default heater mapping) M308 S0 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin e0temp M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0 M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H0 S290 ; set temperature limit for heater 0 to 290C ; BLTouch - Heaters M307 H7 A-1 C-1 D-1 ; Disable the 7th Heater to free up PWM channel 5 on the Duex board. ; Fans M950 F0 C"fan1" Q500 ; create fan 0 on pin fan1 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off ; Tools M563 P0 S"HE0" D0 H0 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue M501 ; load saved parameters from non-volatile memory M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss