; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.1 on Sat May 30 2020 19:30:41 GMT-0600 (Mountain Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"X5SA Pro" ; set printer name M575 P1 S1 B56700 M669 K1 ; select CoreXY mode M555 P2 ; Look like marlin ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards M569 P1 S0 ; physical drive 1 goes backwards M569 P2 S1 ; physical drive 2 goes forwards M569 P3 S1 ; physical drive 2 goes forwards M569 P4 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z4:2 E3 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z401.00 E415 ; set steps per mm M566 X600.00 Y600.00 Z120.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X8000.00 Y8000.00 Z1800.00 E7200.00 ; set maximum speeds (mm/min) M201 X6000.00 Y6000.00 Z100.00 E10000.00 ; set accelerations (mm/s^2) M906 X1100 Y1100 Z1100 E1100 I50 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout M671 X105:395 Y160:160 S2.0 ;Leadscrews at middle left and middle right (S0 is correction value) ; Axis Limits M208 X-2 Y-4 Z0 S1 ; set axis minima M208 X330 Y330 Z380 S0 ; set axis maxima ; Endstops M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop M574 Z1 S2 ; configure active-high endstop for low end on Z via pin !e1stop ; Filament sensor M591 D0 P2 C"e0stop" S1 ; Filament runout Sensor for Extruder E0 on E1 Endstop input P1 = signal HIGH. ; Z-Probe M558 P1 C"!zprobe.in" H5 F500 T10000 ; set Z probe type to switch and the dive height + speeds G31 P500 X-35 Y-0 Z1.15 ; set Z probe trigger value, offset and trigger height M557 X8:330 Y15:315 S98 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"fan2" Q500 M106 P2 S.2 H-1 ; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X6 Y5 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C M501 ; Custom settings are not defined