=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.2.2 running on Duet WiFi 1.02 or later
Board ID: 08DGM-956GU-DJMSN-6JTDA-3SJ6S-TAN7D
Used output buffers: 5 of 24 (20 max)
=== RTOS ===
Static ram: 23460
Dynamic ram: 73296 of which 44 recycled
Never used RAM 15280, free system stack 189 words
Tasks: NETWORK(ready,182) HEAT(blocked,308) MAIN(running,451) IDLE(ready,20)
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:00:24 ago, cause: power up
Last software reset at 2021-03-18 23:42, reason: HeatTaskStuck, GCodes spinning, available RAM 15212, slot 2
Software reset code 0x4143 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f80f BFAR 0xe000ed38 SP 0x20003424 Task IDLE Freestk 34 ok
Stack: 004549a1 004553aa 61000000 a5a5a5a5 004549a1 a5a5a5a5 2000408c 024debda 20001804 20004634 2000343c 2000462c 00000004 20001400 20001400 2000343c 00000000 00000001 2000349c 4e49414d 00000000 00000000 00000001 00000000 00000001 00000001 00000000
Error status: 0x00
Aux0 errors 0,0,0
MCU temperature: min 39.9, current 42.6, max 43.1
Supply voltage: min 23.8, current 24.1, max 24.9, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: position 95998, standstill, SG min/max not available
Driver 1: position 95998, standstill, SG min/max not available
Driver 2: position 95998, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-03-18 23:43:37
Cache data hit count 29251018
Slowest loop: 11.64ms; fastest: 0.25ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 14.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is ready with "m122 " in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 53.77ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address ec:fa:bc:01:d5:77
WiFi Vcc 3.36, reset reason Power up
WiFi flash size 4194304, free heap 23912
WiFi IP address 192.168.11.233
WiFi signal strength -70dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 4 4 0 0 0 0 0 0
=== Filament sensors ===
Extruder 0: pos 0.00, errs: frame 0 parity 0 ovrun 0 pol 0 ovdue 0