3/29/2021, 10:43:25 AM: M122: === Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3beta2 running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956BA-NA3TJ-6J1DJ-3SN6K-19AUU
Used output buffers: 1 of 40 (11 max)
=== RTOS ===
Static ram: 148476
Dynamic ram: 92932 of which 0 recycled
Never used RAM 112784, free system stack 200 words
Tasks: NETWORK(ready,204) ETHERNET(notifyWait,124) HEAT(delaying,303) CanReceiv(notifyWait,907) CanSender(notifyWait,374) CanClock(delaying,353) TMC(notifyWait,94) MAIN(running,1113) IDLE(ready,19)
Owned mutexes:
=== Platform ===
Last reset 00:00:28 ago, cause: software
Last software reset at 2021-03-29 10:42, reason: User, GCodes spinning, available RAM 112784, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Aux1 errors 0,0,0
MCU temperature: min 20.8, current 21.3, max 21.9
Supply voltage: min 24.1, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 30915, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 30915, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 30915, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 30918, writes 11 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 30919, writes 11 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 30919, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2021-03-29 10:43:19
Slowest loop: 5.01ms; fastest: 0.06ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 3.6ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 2 is on, I-accum = 0.0
Heater 3 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== CAN ===
Messages queued 212, send timeouts 0, received 8, lost 0, longest wait 1ms for reply type 6018, peak Tx sync delay 4, free buffers 49 (min 48)
=== Network ===
Slowest loop: 7.08ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 3 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0
3/29/2021, 10:43:32 AM: M122 B40: Diagnostics for board 40:
Board SAMMYC21 firmware 3.1.0+ (2020-07-20b1)
Never used RAM 10.7Kb, max stack 336b
HEAT 1296 CanAsync 1464 CanRecv 1424 AIN 568 MAIN 2308
Last reset 00:00:36 ago, cause: software
External motor driver(s)
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
MCU temperature: min 21.4C, current 21.6C, max 21.8C
Ticks since heat task active 21, ADC conversions started 18383, completed 18383, timed out 0
Last sensors broadcast 00000000 found 0 24 ticks ago
Free CAN buffers: 36
NVM user row b1d088af fffff8bb ffffffff ffffffff
TSENS 000873 GAIN 016177 OFFS 0028e5 CAL 1f2a
3/29/2021, 10:43:36 AM: M122 B41: Diagnostics for board 41:
Board SAMMYC21 firmware 3.1.0+ (2020-07-20b1)
Never used RAM 10.7Kb, max stack 336b
HEAT 1296 CanAsync 1464 CanRecv 1424 AIN 600 MAIN 2308
Last reset 00:00:40 ago, cause: software
External motor driver(s)
Moves scheduled 0, completed 0, in progress 0, hiccups 0
No step interrupt scheduled
MCU temperature: min 20.4C, current 20.4C, max 20.6C
Ticks since heat task active 112, ADC conversions started 20428, completed 20428, timed out 0
Last sensors broadcast 00000000 found 0 116 ticks ago
Free CAN buffers: 36
NVM user row b1d088af fffff8bb ffffffff ffffffff
TSENS 0007f4 GAIN 015f2b OFFS 0024da CAL 1f2a